manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Fixing

2.

Wheel speed sensor

3.

Position the caliper over the disc ensuring the pads are correctly aligned on both sides of the disc.

23.

Fit the caliper retaining bolts and tighten to 

40 Nm

.

24.

Fit the rear wheel (see Rear Wheel - Installation).

25.

With the weight of the motorcycle on its wheels, hold the drop link to swinging arm bolt while tightening the
nut to 

85 Nm

.

26. 

Check and, if necessary, adjust the oil level in the rear bevel box (see Rear Bevel Box Oil Level Check).

27.

Reconnect the battery, positive (red) lead first.

28.

Fit the rider's seat (see Rider’s Seat - Installation).

29.

Check for correct brake operation. Rectify as necessary.

30.

Rear Bevel Box Bearings - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the rear bevel box (see Rear Bevel Box - Removal).

1.

With the aid of an assistant holding the rear bevel box, align the drive shaft such that it is straight.

2.

Using a soft faced mallet, give a sharp tap to one of the universal joint yokes on the drive shaft, indicated
below, to release the snap ring securing the drive shaft to the bevel box.

3. 

1

chne

Universal joint yoke

1.

Remove the drive shaft.

4.

Note

When removing the bearing outer race, the cap will separate from the outer race.

Fit T3880627 - Bearing Puller, 32-42 mm such that the lugs of the tool are between the bearing outer race
and its cap.

5. 

Assemble T3880627 - Bearing Puller, 32-42 mm to T3880208 - Slide Hammer, fully engaging the threads.

6.

Draw back the slide part of the hammer swiftly to facilitate the removal of the bearing outer race.

7.

2

3

4

Tiger Explorer XR Series

445 of 746

REAR BEVEL BOX / DRIVE SHAFT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Kappa K132 Manual preview
K132
Бренд: Kappa Страницы: 4
PZRacing GearTronic ZERO GT3100-K1 User Manual preview
GearTronic ZERO GT3100-K1
Бренд: PZRacing Страницы: 2
Regal Raptor DAYTONA 125 User Manual preview
DAYTONA 125
Бренд: Regal Raptor Страницы: 48
BMW K 1200 LT Repair Manual preview
K 1200 LT
Бренд: BMW Страницы: 16
Honda CB TWISTER (Spanish) Manual Del Propietario preview
CB TWISTER
Бренд: Honda Страницы: 93
Garmin Montana 7 Series Installation Instructions Manual preview
Montana 7 Series
Бренд: Garmin Страницы: 24
Triumph ACCESORIES 2005 Price List preview
ACCESORIES 2005
Бренд: Triumph Страницы: 6
Triumph Clothing Range 2006 Catalog preview
Clothing Range 2006
Бренд: Triumph Страницы: 19
Triumph 2007 ROCKET III Overview preview
2007 ROCKET III
Бренд: Triumph Страницы: 20
Triumph Speed Triple Handbook preview
Speed Triple
Бренд: Triumph Страницы: 136
Triumph Speed Triple 1200 RS Owner'S Handbook Manual preview
Speed Triple 1200 RS
Бренд: Triumph Страницы: 184
Triumph Scrambler 1200 XC Service Manual preview
Scrambler 1200 XC
Бренд: Triumph Страницы: 640
Kobalt SGY-A13 Manual preview
SGY-A13
Бренд: Kobalt Страницы: 33
Athena EFI 2T ECU Installation Manual preview
EFI 2T ECU
Бренд: Athena Страницы: 88
Denali D2 Instruction Manual preview
D2
Бренд: Denali Страницы: 3
Benelli TORNADO Tre Novecento 900 Owner'S Manual preview
TORNADO Tre Novecento 900
Бренд: Benelli Страницы: 48
Benelli Tre 1130 K Owner'S Manual preview
Tre 1130 K
Бренд: Benelli Страницы: 108
Benelli TRK 502 Service Station Manual preview
TRK 502
Бренд: Benelli Страницы: 408

Бренды по названию

Популярные бренды

Загрузить еще бренды