manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Connect the brake hose(s) to the caliper incorporating new sealing washers on each side of the union(s).
Ensure that the brake hose is located into its retaining lug on the mudguard.

11. 

Tighten the brake hose union bolt to 

25 Nm

.

12. 

WARNING

Use only DOT 4 specification brake fluid as listed in the general information section of this manual. The use
of brake fluids other than those DOT 4 fluids listed in the general information section may reduce the
efficiency of the braking system leading to loss of motorcycle control and an accident.
Observe the brake fluid handling warnings given earlier in this section of the manual.

CAUTION

To prevent paint damage, do not spill brake fluid onto any area of the bodywork. Spilled brake fluid will
damage paintwork.

Fill the master cylinder with new, DOT 4 brake fluid from a sealed container.
Bleed the front brakes (see Bleeding the Front Brakes, Renewing Brake Fluid).
Check the brakes for correct operation. Rectify any faults as necessary.

WARNING

It is dangerous to operate the motorcycle with defective brakes; you must have your authorised Triumph
dealer take remedial action before you attempt to ride the motorcycle again. Failure to take remedial action
may reduce braking efficiency leading to loss of motorcycle control and an accident.

Front Discs - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

WARNING

Do not renew front brake discs individually. Discs must always be renewed in pairs even if one of a pair is
serviceable.
A dangerous riding condition leading to an accident could result if this warning is ignored.

Remove the front wheel (see Front Wheel - Removal).

1.

Support the wheel on blocks as illustrated to avoid damage to the wheel centre.

2.

1

Tiger Explorer XR Series

473 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

3M Speedglas G5-02 User Manual preview
Speedglas G5-02
Бренд: 3M Страницы: 17
3M Speedglas 9100 MP Manual preview
Speedglas 9100 MP
Бренд: 3M Страницы: 72
3M SPEEDGLAS SL User Manual preview
SPEEDGLAS SL
Бренд: 3M Страницы: 84
Metra Electronics Saddle Tramp BC-BTHBSP Installation Instructions Manual preview
Saddle Tramp BC-BTHBSP
Бренд: Metra Electronics Страницы: 8
Razor Rebellion Electric Chopper 15130760 Owner'S Manual preview
Rebellion Electric Chopper 15130760
Бренд: Razor Страницы: 17
AMFD RideMaxx Quick Start Manual preview
RideMaxx
Бренд: AMFD Страницы: 17
Honda ST1300 2004 Setup Instructions preview
ST1300 2004
Бренд: Honda Страницы: 26
Garmin REACTOR 40 KICKER SUZUKI ADAPTER Installation Instructions Manual preview
REACTOR 40 KICKER SUZUKI ADAPTER
Бренд: Garmin Страницы: 40
Saddlemen FTB Series Installation Instruction preview
FTB Series
Бренд: Saddlemen Страницы: 6
Shark RSR2 Owner'S Manual preview
RSR2
Бренд: Shark Страницы: 24
Malaguti X3M User Manual preview
X3M
Бренд: Malaguti Страницы: 292
Hermes LCD 9.13G Manual preview
LCD 9.13G
Бренд: Hermes Страницы: 23
RIEJU CENTURY 125IE Owner'S Manual preview
CENTURY 125IE
Бренд: RIEJU Страницы: 34
Baotian BT49QT-3 Service Manual preview
BT49QT-3
Бренд: Baotian Страницы: 30
6KU FIXIE Step By Step Building Manual preview
FIXIE
Бренд: 6KU Страницы: 17
KED Quicksafe Instructions For Use Manual preview
Quicksafe
Бренд: KED Страницы: 52
M8-TECH CITY M8 Operator'S Manual preview
CITY M8
Бренд: M8-TECH Страницы: 12
DK Custom DK-LPR-AX-CRV-22 Quick Start Manual preview
DK-LPR-AX-CRV-22
Бренд: DK Custom Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды