manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

For example:
Crankshaft Journal diameter 37.962 mm
Crankcase Bore 41.125 mm
Bearing Required Blue

Note

It is normal for the bearings selected to differ from one journal to another.
It is also normal for there to be two options of bearing shell colour. In such cases, pick the shell size
which gives the greater running clearance.

CAUTION

Always confirm, using the Plastigauge method, that the running clearance is correct before final assembly.
Severe engine damage could result from incorrect clearance.

Crankshaft End Float

For specifications refer toCrankshaft.

Note

Crankshaft end float is controlled by the tolerances in crankshaft and crankcase machining. No
thrust washers are used. If crankshaft end float is outside the specified limit, the crankshaft and/or
the crankcases must be replaced.

Piston Wear Check

Note

It is not necessary to remove the connecting rods from the crankshaft.

Remove the cylinder head (see Cylinder Head - Removal).
Remove the cylinder liner (see Cylinder Liners - Removal).
Remove the gudgeon pin circlip from one side of the piston.

1. 

cape

Removing the Gudgeon Pin Circlip

CAUTION

Never force the gudgeon pin through the piston. This may cause damage to the piston which may also
damage the liner when assembled.

Tiger Explorer XR Series

156 of 746

CRANKSHAFT / RODS / PISTONS

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Baotian BT50QT-9 Service Manual preview
BT50QT-9
Бренд: Baotian Страницы: 30
Yamaha YZ250F(R) Owner'S Service Manual preview
YZ250F(R)
Бренд: Yamaha Страницы: 662
hepco & becker 6304567 00 01 Quick Start Manual preview
6304567 00 01
Бренд: hepco & becker Страницы: 4
Leatt Body Protector 4.5 Junior Manual preview
Body Protector 4.5 Junior
Бренд: Leatt Страницы: 40
kellermann Jetstream Installation Manual preview
Jetstream
Бренд: kellermann Страницы: 7
PUIG 0295 Mounting Instructions preview
0295
Бренд: PUIG Страницы: 2
Honeywell EV1 User'S Information Manual preview
EV1
Бренд: Honeywell Страницы: 8
Honeywell HW100 Important Instructions & Warnings preview
HW100
Бренд: Honeywell Страницы: 304
hepco & becker 5039515 00 05 Quick Start Manual preview
5039515 00 05
Бренд: hepco & becker Страницы: 3
Malaguti F18 WARRIOR Manual preview
F18 WARRIOR
Бренд: Malaguti Страницы: 383
Yamaha YZF-R1P 2001-2003 Assembly Manual preview
YZF-R1P 2001-2003
Бренд: Yamaha Страницы: 26
Yamaha YZF-R1 2003 Supplementary Service Manual preview
YZF-R1 2003
Бренд: Yamaha Страницы: 36
Yamaha YZF-R1 2002 Service Information preview
YZF-R1 2002
Бренд: Yamaha Страницы: 47
Yamaha YZF-R1LEVC Supplementary Service Manual preview
YZF-R1LEVC
Бренд: Yamaha Страницы: 87
Yamaha YZF-R1S Owner'S Manual preview
YZF-R1S
Бренд: Yamaha Страницы: 106
Yamaha YZF-R1T Owner'S Manual preview
YZF-R1T
Бренд: Yamaha Страницы: 114
Yamaha YZF-R1 2000 Supplementary Service Manual preview
YZF-R1 2000
Бренд: Yamaha Страницы: 78
Yamaha YZF-R1Z Owner'S Manual preview
YZF-R1Z
Бренд: Yamaha Страницы: 120

Бренды по названию

Популярные бренды

Загрузить еще бренды