manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

motorcycle control and an accident.

WARNING

Before installation, all internal brake components should be cleaned and lubricated with clean new DOT 4
brake fluid.
Never use solvents, petrol (gasoline), engine oil, or any other petroleum distillate on internal brake
components as this will cause deterioration of the hydraulic seals in the calipers and master cylinders.
A dangerous riding condition leading to loss of motorcycle control and an accident could result if this warning
is ignored.

If all components are serviceable, obtain a piston seal kit and reassemble the caliper as follows:

Ensure all components are clean, then fit the new seals to their grooves in the caliper bores.

1. 

Lubricate the fluid seals, caliper bore and the outside of the pistons with clean DOT 4 brake fluid.

2.

Ease the pistons squarely back into the bores, taking care not to displace the seals.

3.

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Thoroughly clean the threaded fixing holes for the front fork brake caliper fixings.

1.

Thoroughly clean the threaded part of the brake caliper fixings and smear the first four threads with a
proprietary copper based grease.

2. 

Position the brake caliper over the disc.

3.

Secure the brake caliper with the fixings and tighten sufficiently to bring the caliper into contact with its
mounting points, while allowing a small amount of lateral movement. Do not fully tighten at this stage.

4. 

1

2

Caliper

1.

Fixings

2.

Note

Before tightening, the brake caliper should be positioned such that it is aligned as centrally as
possible over the brake disc.

Visually check the clearances between the caliper body and brake disc in the four locations shown below.

5.

Tiger Explorer XR Series

471 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

hepco & becker TRIUMPH Bonneville T 120 Quick Start Manual preview
TRIUMPH Bonneville T 120
Бренд: hepco & becker Страницы: 4
R&G LP0107BK Fitting Instructions Manual preview
LP0107BK
Бренд: R&G Страницы: 14
X-lite X-901 Directions For Use Manual preview
X-901
Бренд: X-lite Страницы: 84
R&G CP0482 Fitting Instructions Manual preview
CP0482
Бренд: R&G Страницы: 18
Vance and hines 48421 Installation Instructions preview
48421
Бренд: Vance and hines Страницы: 5
Custom Dynamics Magic Strobes Installation Instructions preview
Magic Strobes
Бренд: Custom Dynamics Страницы: 2
Royal Enfield ELECTRA Service Manual preview
ELECTRA
Бренд: Royal Enfield Страницы: 234
Bosch GHJ 10,8+18V Unisex Original Instructions Manual preview
GHJ 10,8+18V Unisex
Бренд: Bosch Страницы: 14
Bosch LTE65 Manual preview
LTE65
Бренд: Bosch Страницы: 28
Bosch 06188000DY Original Instructions Manual preview
06188000DY
Бренд: Bosch Страницы: 145
Arai CT-Z Instructions For Use Manual preview
CT-Z
Бренд: Arai Страницы: 15
SpeedAngle GMOS JI100S User Manual preview
GMOS JI100S
Бренд: SpeedAngle Страницы: 37
Saddlemen I14-07 Series User'S Manual & Installation Instructions preview
I14-07 Series
Бренд: Saddlemen Страницы: 2
Saddlemen Express Trunk Bag Installation Instructions preview
Express Trunk Bag
Бренд: Saddlemen Страницы: 2
Ermax SV 650 1999 Fitting Instructions preview
SV 650 1999
Бренд: Ermax Страницы: 2
Malaguti X3M User Manual preview
X3M
Бренд: Malaguti Страницы: 292
Yamaha BWS CW50L Owner'S Manual preview
BWS CW50L
Бренд: Yamaha Страницы: 68
Denali DialDim Instruction Manual preview
DialDim
Бренд: Denali Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды