manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

1

cfeg

Locating devices

1.

Facing blade

2.

Release the three hooks and remove the facing blade.

4.

1

cfeh

Hooks

1.

Camshaft Drive Chain Tensioner Blade - Assembly

Assembly is the reverse of disassembly (see Camshaft Drive Chain Tensioner Blade - Disassembly).

1.

Camshaft Drive Chain, Tensioner Blade and Rubbing Strip - Installation

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Loosely refit the rubbing blade. Do not fit the pin at this stage.

1.

Lower the chain through the cylinder head opening and hook over the crankshaft sprocket. Support the
chain at its upper end until the camshafts are refitted.

2. 

Refit the tensioner blade, ensuring that the camshaft drive chain is correctly seated on the facing blade and
secure with the pin.

3. 

Reposition the rubbing blade, ensuring that the camshaft drive chain is correctly seated on the rubbing blade
and secure with the pin.

4. 

Refit the camshafts (see Camshafts - Installation).

Cylinder Head - Removal

Tiger Explorer XR Series

104 of 746

CYLINDER HEAD

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

X-lite CLEO Installation Instructions preview
CLEO
Бренд: X-lite Страницы: 5
Qingqi QM110GY Owner'S Manual preview
QM110GY
Бренд: Qingqi Страницы: 48
Yamaha Star XV250ZC Owner'S Manual preview
Star XV250ZC
Бренд: Yamaha Страницы: 96
R&G ECC0300R Fitting Instructions Manual preview
ECC0300R
Бренд: R&G Страницы: 6
Happy Trails KTM950 Quick Start Manual preview
KTM950
Бренд: Happy Trails Страницы: 4
MOSKO MOTO Scout 25L Pannier Kit V2.0 Installation Instructions Manual preview
Scout 25L Pannier Kit V2.0
Бренд: MOSKO MOTO Страницы: 13
Zero SR/S Service Manual preview
SR/S
Бренд: Zero Страницы: 290
Fantic XX 125 Use And Maintenance Manual preview
XX 125
Бренд: Fantic Страницы: 153
Yamaha YZ 2019 Series Owner'S Service Manual preview
YZ 2019 Series
Бренд: Yamaha Страницы: 398
Yamaha YZ250F(P)/LC Owner'S Service Manual preview
YZ250F(P)/LC
Бренд: Yamaha Страницы: 666
Yamaha YZ250F(Y) Owner'S Service Manual preview
YZ250F(Y)
Бренд: Yamaha Страницы: 190
Shark RIDILL Owner'S Manual preview
RIDILL
Бренд: Shark Страницы: 92
Memphis Shades MEM-9890 Mounting Instructions preview
MEM-9890
Бренд: Memphis Shades Страницы: 2
Memphis Shades 2321-0045 Mounting Instructions preview
2321-0045
Бренд: Memphis Shades Страницы: 2
Memphis Shades 2320-0037 Mounting Instructions preview
2320-0037
Бренд: Memphis Shades Страницы: 2
HYOSUNG XRX125d Owner'S Manual preview
XRX125d
Бренд: HYOSUNG Страницы: 74
VOIGT MT 26860 Assembly Instructions preview
26860
Бренд: VOIGT MT Страницы: 2
KFI HK-150 Quick Start Manual preview
HK-150
Бренд: KFI Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды