manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

ECM Connector Pin Numbering

The above illustration shows the pin numbering system used in the engine management circuit diagram.
The smaller connector's pins are prefixed A and the larger connector pins B. As viewed on the mating face with
the ECM (as per the illustration), pins are numbered from right to left with number one in the top right corner.

Triumph Diagnostic Software - Engine ECM

Cruise Control Switch Check

Described on the following pages is the range of information which can be retrieved from the engine ECM’s
memory and the adjustments which can be performed using the Triumph diagnostic software.
The tables indicate which tests are performed by the on-board system and what information can be retrieved by
the Triumph diagnostic software.

Note

Full details of how to operate the software can be found in the Triumph Diagnostic Tool User Guide,
which can be downloaded by authorised Triumph dealers from www.triumphonline.net.

Build Data

The Build Data screen will display the following information:

Motorcycle model
Vehicle Identification Number (VIN)
ECM type
ECM ID
ECM serial number
Tune number
Date of last tune download
Total tune downloads since manufacture
The lock status of the Engine ECM (ECM Locked, Unlocked or Not Applicable).

Current Data

The data available under Current Data is:

Function Examined

Result Reported (Scale)

Fuel system status

open or closed loop operation

Tiger Explorer XR Series

244 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

N-Com B902 Quick Start Manual preview
B902
Бренд: N-Com Страницы: 2
N-Com MCS II Safety And Instructions For Use preview
MCS II
Бренд: N-Com Страницы: 64
Honda Soft Luggage Pannier Racks Installation Manuallines preview
Soft Luggage Pannier Racks
Бренд: Honda Страницы: 10
KTM 690 Enduro R 2013 Repair Manual preview
690 Enduro R 2013
Бренд: KTM Страницы: 234
Victory Motorcycles 2005-2006 Hammer Service Manual preview
2005-2006 Hammer
Бренд: Victory Motorcycles Страницы: 12
MRA 4025066171910 Mounting Instructions preview
4025066171910
Бренд: MRA Страницы: 9
PUIG 21226 Mounting Instructions preview
21226
Бренд: PUIG Страницы: 6
hepco & becker Easyrack 6612533 01 01 Manual preview
Easyrack 6612533 01 01
Бренд: hepco & becker Страницы: 5
National Cycle ZTechnik Z2386 Quick Start Manual preview
ZTechnik Z2386
Бренд: National Cycle Страницы: 2
Yamaha YZFR6X(C) Owner'S Manual preview
YZFR6X(C)
Бренд: Yamaha Страницы: 120
DYNATEK DDK1-11 Installation Manual preview
DDK1-11
Бренд: DYNATEK Страницы: 11
Husqvarna 2008 SMR 450-R Parts Catalog preview
2008 SMR 450-R
Бренд: Husqvarna Страницы: 107
Husqvarna 125/2002 Owner'S Manual preview
125/2002
Бренд: Husqvarna Страницы: 280
Husqvarna 2005 SM 125 S Owner'S Manual preview
2005 SM 125 S
Бренд: Husqvarna Страницы: 162
Husqvarna F2101Q1 Repair Manual preview
F2101Q1
Бренд: Husqvarna Страницы: 321
Husqvarna 2004 CR 250 Workshop Manual preview
2004 CR 250
Бренд: Husqvarna Страницы: 364
Husqvarna 2004 DUAL PURPOSE SM 610 Owner'S Manual preview
2004 DUAL PURPOSE SM 610
Бренд: Husqvarna Страницы: 188
Husqvarna 2006 SMS 125S Workshop Manual preview
2006 SMS 125S
Бренд: Husqvarna Страницы: 269

Бренды по названию

Популярные бренды

Загрузить еще бренды