manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the rear wheel (see Rear Wheel - Removal).

1. 

Remove the rear brake disc (see Rear Brake Disc - Removal).

2.

Remove and discard the five fixings and remove the pulser ring.

3.

1

1

1

2

3

Fixings

1.

Pulser ring

2.

Hub

3.

Rear ABS Pulser Ring - Inspection

Check the pulser ring for damaged, missing or cracked teeth or distortion. Renew the pulser ring as
necessary.

1. 

Rear ABS Pulser Ring - Installation

Locate the pulser ring to the hub.

1.

Install new fixings and tighten to 

5 Nm

.

2.

Refit the rear brake disc (see Rear Brake Disc - Installation).
Refit the rear wheel (see Rear Wheel - Installation).
Check that the brakes operate correctly.

WARNING

It is dangerous to operate the motorcycle with defective brakes; you must have your authorised Triumph
dealer take remedial action before you attempt to ride the motorcycle again. Failure to take remedial action
may reduce braking efficiency leading to loss of motorcycle control and an accident.

ABS Hydraulic Modulator/ECM - Removal

ABS Hydraulic Modulator/ECM - Installation

WARNING

Tiger Explorer XR Series

501 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

N-Com R Series User Instructions And Safety preview
R Series
Бренд: N-Com Страницы: 28
Caberg HORUS Manual preview
HORUS
Бренд: Caberg Страницы: 16
Cake Makka Quick Start Manual preview
Makka
Бренд: Cake Страницы: 13
S&B Filters 76-6000 Installation Instructions Manual preview
76-6000
Бренд: S&B Filters Страницы: 7
Öhlins POF5K00 Mounting Instructions preview
POF5K00
Бренд: Öhlins Страницы: 2
Öhlins Mechatronics 35007-01 Installation Instruction preview
Mechatronics 35007-01
Бренд: Öhlins Страницы: 4
Öhlins McPherson Strut MIR 5H02 Mounting Instructions preview
McPherson Strut MIR 5H02
Бренд: Öhlins Страницы: 2
Öhlins KA 590 Mounting Instructions preview
KA 590
Бренд: Öhlins Страницы: 4
DMC 25470-00 Installation Instructions preview
25470-00
Бренд: DMC Страницы: 2
Velmia Premium Motorcycle Cover Instructions For Use Manual preview
Premium Motorcycle Cover
Бренд: Velmia Страницы: 32
Jialing Honda MOTO NZ50 Assembly Instructions Manual preview
MOTO NZ50
Бренд: Jialing Honda Страницы: 10
Cycle Protect The Liberator Installation & Owner'S Manual preview
The Liberator
Бренд: Cycle Protect Страницы: 15
KTM F8103S4 Setup Instructions preview
F8103S4
Бренд: KTM Страницы: 36
Yamaha RMAX WOLVERINE 2021 Owner'S Manual preview
RMAX WOLVERINE 2021
Бренд: Yamaha Страницы: 192
Yamaha YZ 2015 Series Owner'S Service Manual preview
YZ 2015 Series
Бренд: Yamaha Страницы: 396
Yamaha YXF10WRAN Owner'S Manual preview
YXF10WRAN
Бренд: Yamaha Страницы: 192
BMW S 1000 RR - Brochure preview
S 1000 RR -
Бренд: BMW Страницы: 19
hepco & becker 506016-7 Quick Start Manual preview
506016-7
Бренд: hepco & becker Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды