manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Refit the airbox (see Airbox - Installation).
Refit the fuel tank (see Fuel Tank - Installation).
Reconnect the battery positive, (red) lead first and tighten the terminals to 

4.5 Nm

.

Refit the rider’s seat (see Rider’s Seat - Installation).

Throttle Actuator Motor

CAUTION

The fixings for the throttle position sensor must not be loosened or removed.
If the throttle position sensor fixings have been loosened or removed, the throttle body assembly must be
replaced as there are no means to reset throttle position sensor to its correct position.

Note

If the throttle position sensor fixings have been loosened or removed, any warranty claims for the
throttle bodies will be rejected.

cjit

1

2

Throttle position sensor

1.

Fixings

2.

The throttle position sensor can not be removed, replaced or adjusted in service. If necessary, the throttle bodies
and throttle position sensor must be replaced as an assembly.

Engine Management Adaption

The throttle actuator motor is an integral part of the throttle bodies and cannot be replaced separately.

Exhaust System - Removal

Note

After the engine management adaption has been reset on this model, the Cruise Control Switch
Check Function Test must be performed (see Cruise Control Switch Check). After the adaptions have
been reset, DTC 1575 (cruise control disabled until button press sequence completed) will be stored,
and the cruise control disabled, until the function test is completed.

General Information

The engine management system fitted to this model is adaptive. This means that the system is able to learn
about new or changing operating conditions and continuously adapt itself without needing to constantly make

Tiger Explorer XR Series

331 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

DAELIM S3 Service Manual preview
S3
Бренд: DAELIM Страницы: 20
yasuni TUB653 Assembly Instructions Manual preview
TUB653
Бренд: yasuni Страницы: 8
Dennis Kirk IGNITE 509 Instruction Manual preview
IGNITE 509
Бренд: Dennis Kirk Страницы: 5
Yoshimura 070BG125511 Manual preview
070BG125511
Бренд: Yoshimura Страницы: 4
Suzuki GSX-R600 Manual preview
GSX-R600
Бренд: Suzuki Страницы: 165
Pandora Smart Moto Manual preview
Smart Moto
Бренд: Pandora Страницы: 56
SpeedAngle GMOS JI100S User Manual preview
GMOS JI100S
Бренд: SpeedAngle Страницы: 37
G PLAST 2402-BB Information For Users preview
2402-BB
Бренд: G PLAST Страницы: 4
hepco & becker 6302513 00 01 Manual preview
6302513 00 01
Бренд: hepco & becker Страницы: 3
Yamaha TT 600 R 1997 Service Information preview
TT 600 R 1997
Бренд: Yamaha Страницы: 42
Yamaha T2125 Parts List preview
T2125
Бренд: Yamaha Страницы: 43
Yamaha TT-R110E(Y) Owner'S Manual preview
TT-R110E(Y)
Бренд: Yamaha Страницы: 80
Yamaha TT-R0EX Owner'S Manual preview
TT-R0EX
Бренд: Yamaha Страницы: 78
Yamaha TT-R110E(Z) Owner'S Manual preview
TT-R110E(Z)
Бренд: Yamaha Страницы: 84
Yamaha TT-230RA Owner'S Manual preview
TT-230RA
Бренд: Yamaha Страницы: 80
Yamaha TT-R110E Owner'S Manual preview
TT-R110E
Бренд: Yamaha Страницы: 90
Yamaha TT-R 110 Owner'S Manual preview
TT-R 110
Бренд: Yamaha Страницы: 88
Yamaha TT-R TT250R Owner'S Manual preview
TT-R TT250R
Бренд: Yamaha Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды