manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Petrol (gasoline) is highly flammable and can be explosive under certain conditions. When opening the fuel
tank cap always observe all the following items:
Turn the motorcycle ignition switch OFF.
Do not smoke.
Always have a fire extinguisher containing FOAM, CO2, HALON or POWDER close at hand when handling
or draining fuel or fuel systems. Fire extinguishers must also be present in areas where fuel is stored.
Always disconnect the vehicle battery, negative (black) lead first, before carrying out, dismantling or draining
work on a fuel system.
Whenever petrol (gasoline) is being handled, drained, stored or when fuel systems are being dismantled,
make sure the area is well ventilated. All potential forms of ignition must be extinguished or removed (this
includes any appliance with a pilot light). Any lead-lamps must be flame-proof and kept clear of any fuel
spillage.
Warning notices must be posted at a safe distance from the site of the work to warn others that petrol
(gasoline) is being openly handled. The notice must instruct the reader of the precautions which must be
taken.
Failure to observe any of the above warnings may lead to a fire hazard which could result in personal injury.

WARNING

No one should be permitted to repair components associated with petrol (gasoline) without first having
specialist training on the fire hazards which may be created by incorrect installation and repair of items
associated with petrol (gasoline).
Repairs carried out by untrained personnel could bring about a safety hazard leading to a risk of personal
injury.

WARNING

Draining or extraction of petrol (gasoline) from a vehicle fuel tank must be carried out in a well ventilated
area.
The receptacle used to contain the petrol (gasoline) must be more than adequate for the full amount of fuel
to be extracted or drained. The receptacle should be clearly marked with its contents, and placed in a safe
storage area which meets the requirements of local authority regulations.
When petrol (gasoline) has been extracted or drained from a fuel tank, the precautions governing naked
lights and ignition sources should be maintained.
Failure to observe any of the above warnings could bring about a safety hazard leading to a risk of personal
injury.

Fuel Tank Removal

Fuel tanks should have a 'PETROL (GASOLINE) VAPOUR' warning label attached to them as soon as they are
removed from the vehicle. In all cases, they must be stored in a secured, marked area.

Chassis Repairs

WARNING

If the motorcycle is involved in an accident or collision it must be taken to an authorised Triumph dealer for
repair or inspection. Any accident can cause damage to the motorcycle, which if not correctly repaired, may
cause a second accident which may result in injury or death.
The frame must not be modified as any modification to the frame such as welding or drilling may weaken the
frame resulting in an accident.

Tiger Explorer XR Series

12 of 746

GENERAL INFORMATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Uclear AMP Series User Manual preview
AMP Series
Бренд: Uclear Страницы: 2
Saddlemen 813-27-all User'S Manual & Installation Instructions preview
813-27-all
Бренд: Saddlemen Страницы: 3
Bajaj PULSAR NS200 Manual preview
PULSAR NS200
Бренд: Bajaj Страницы: 39
Two Brothers Racing 005-3860405-S1 Installation Instructions preview
005-3860405-S1
Бренд: Two Brothers Racing Страницы: 2
UBCO 2X2 SE 2023 User Manual preview
2X2 SE 2023
Бренд: UBCO Страницы: 27
SHERCO SHERCO 50 SE 2022 Owner'S Manual preview
SHERCO 50 SE 2022
Бренд: SHERCO Страницы: 226
Shark RSF 2 RACE Manual preview
RSF 2 RACE
Бренд: Shark Страницы: 8
Yamaha ET250 1980 Manual preview
ET250 1980
Бренд: Yamaha Страницы: 22
Yamaha DT50M Manual And Manual preview
DT50M
Бренд: Yamaha Страницы: 24
Yamaha E115M Owner'S Manual preview
E115M
Бренд: Yamaha Страницы: 61
Yamaha Fino 125 Manual preview
Fino 125
Бренд: Yamaha Страницы: 78
Yamaha Fazer Owner'S Manual preview
Fazer
Бренд: Yamaha Страницы: 79
Yamaha FAZER FZS1000 Owner'S Manual preview
FAZER FZS1000
Бренд: Yamaha Страницы: 94
Yamaha Fazer FZ6-S Owner'S Manual preview
Fazer FZ6-S
Бренд: Yamaha Страницы: 90
Yamaha EGO GEAR Owner'S Manual preview
EGO GEAR
Бренд: Yamaha Страницы: 86
Yamaha Fazer FZ6-SHG Owner'S Manual preview
Fazer FZ6-SHG
Бренд: Yamaha Страницы: 96
Yamaha FAZER FZ1-SA Owner'S Manual preview
FAZER FZ1-SA
Бренд: Yamaha Страницы: 96
Yamaha Fazer FZ6-SAHG Owner'S Manual preview
Fazer FZ6-SAHG
Бренд: Yamaha Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды