manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

13

System Diagnostics

The ABS system has an on-board diagnostics feature which allows service technicians to retrieve stored data
from the ECM using Triumph diagnostic software. Full details of the Triumph diagnostic software operation and
how to interpret the results are given in the Triumph Diagnostic Tool User Guide.
The software is connected, via an interface cable, to the motorcycle using a dedicated diagnostic plug situated
beneath the seat. By using a dedicated plug, no electrical connectors associated with the system are disturbed,
reducing potential connector damage.
The software allows the user to retrieve data associated with the system sensors and actuators, test various
component functions, read build data and make minor adjustments to the set-up of the system. The data and
tests available are described on the following pages.

Diagnostic Tool Connection

Diagnostic Trouble Codes

Diagnostic trouble codes (DTCs) are logged in the ABS ECM memory when there is a confirmed fault in the
system.
The codes are reported to the Triumph Diagnostic Tool as a four digit code.

Triumph Diagnostic Software - ABS

Described on the following pages is the range of information which can be retrieved from the ECM’s memory
and the adjustments which can be performed using the Triumph diagnostic software.
The tables indicate which tests are performed by the on-board system and what information can be retrieved by
the Triumph diagnostic software.

Note

Full details of how to operate the software can be found in the Triumph Diagnostic Tool User Guide,
which can be downloaded by authorised Triumph dealers from www.triumphonline.net.

Build Data

The 

Build Data

 screen will display the following information:

Function Examined

ECM type

ECM ID number

Software version number

Current Data

The 

Current Data

 screen will display the following information:

Function Examined

Result Reported (Scale)

Front wheel speed

km/h

Tiger Explorer XR Series

511 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

X-lite X-903 Ultra Carbon 29 Safety And Instructions For Use preview
X-903 Ultra Carbon 29
Бренд: X-lite Страницы: 116
Happy Trails KTM950 Quick Start Manual preview
KTM950
Бренд: Happy Trails Страницы: 4
Zero DSR 2018 Owner'S Manual preview
DSR 2018
Бренд: Zero Страницы: 162
SCA 394021 Owner'S Instruction Manual preview
394021
Бренд: SCA Страницы: 5
Takegawa Operation and Instruction Manua Operation And Instruction Manual preview
Operation and Instruction Manua
Бренд: Takegawa Страницы: 9
hepco & becker 6303544 00 01 Quick Start Manual preview
6303544 00 01
Бренд: hepco & becker Страницы: 3
PMI Ventilator Instructions preview
Ventilator
Бренд: PMI Страницы: 2
Saddlemen Metric Cruiser Seats User Manual preview
Metric Cruiser Seats
Бренд: Saddlemen Страницы: 3
Royal Enfield Super Meteor 650 Owner'S Manual preview
Super Meteor 650
Бренд: Royal Enfield Страницы: 124
Thermo Soles TS-03 Instructions Manual preview
TS-03
Бренд: Thermo Soles Страницы: 13
Gemini 953NH User'S And Installer'S Manual preview
953NH
Бренд: Gemini Страницы: 17
Baotian BT49QT-7 User Manual preview
BT49QT-7
Бренд: Baotian Страницы: 22
TGB X-MOTION 250 Owner'S Manual preview
X-MOTION 250
Бренд: TGB Страницы: 219
Petzl EIOS-3 Manual preview
EIOS-3
Бренд: Petzl Страницы: 10
RSI HA1002 Installation Instructions preview
HA1002
Бренд: RSI Страницы: 2
Busse COBARA Instructions For Use Manual preview
COBARA
Бренд: Busse Страницы: 24
KTM 60112929050 Information preview
60112929050
Бренд: KTM Страницы: 7
Gazzini 10040330 Instructions For Use Manual preview
10040330
Бренд: Gazzini Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды