manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Front Wheel - Installation

Note

Refer to the chart below for the correct tool and tool face when inserting bearings. Bearings are
inserted by means of a draw-bolt acting on the insertion tool. A support tool is located on the
opposite side of the wheel to the insertion tool and as the bolt is tightened, the bearing is drawn into
the wheel.
Insert bearings with the marked or shielded side facing outwards and always fit a new bearing circlip
and seals.

Bearing Insertion Tool

Support Tool

Left Bearing

T3880053 - Wheel Bearing
Extraction Kit
Large face to bearing

3880070-T0301 - Bearing Installer
Large face to wheel

Right Bearing

T3880053 - Wheel Bearing
Extraction Kit
Large face to bearing

3880070-T0301 - Bearing Installer
Large face to wheel

Fit the wheel bearing to the left hand side of the wheel using the method described above.

1. 

Fit the wheel bearings and centre sleeve using the method described opposite.

2.

1

choo

T3880053 - Wheel Bearing Extraction Kit

1.

Fit a new circlip.

3.

Lubricate and fit new seals to the front wheel. Lubricate the seal’s knife-edge with grease to NLGI 2
specification.

4. 

Fit the front wheel (see Front Wheel - Installation).

5.

Rear Wheel - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Lightly smear the wheel spacers with grease and locate in the hubs as noted for removal.

1.

Position the wheel between the forks ensuring the spacers remain in position on both sides.

2.

Tiger Explorer XR Series

552 of 746

WHEELS / TYRES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Kappa K132 Manual preview
K132
Бренд: Kappa Страницы: 4
LAZER Century User Manual preview
Century
Бренд: LAZER Страницы: 6
GBRacing BA12-6-GBR-SET Fitting Instructions preview
BA12-6-GBR-SET
Бренд: GBRacing Страницы: 2
HYOSUNG 2002 Comet 125 Service Manual preview
2002 Comet 125
Бренд: HYOSUNG Страницы: 199
Saddlemen 813-27-all User'S Manual & Installation Instructions preview
813-27-all
Бренд: Saddlemen Страницы: 3
STARLANE DaVinci RSV4-APRC Installation And Instruction Manual preview
DaVinci RSV4-APRC
Бренд: STARLANE Страницы: 2
TREND AIRPRO MAX User Instructions preview
AIRPRO MAX
Бренд: TREND Страницы: 38
X-lite LIX9U0003740299 Safety And Instructions For Use preview
LIX9U0003740299
Бренд: X-lite Страницы: 116
BoxerCafe Battery Relocation Kit Instruction Sheet preview
Battery Relocation Kit
Бренд: BoxerCafe Страницы: 7
Big Bike Parts 52-571 Installation Instructions preview
52-571
Бренд: Big Bike Parts Страницы: 3
Maico GM STAR 250 1986 Owner'S Manual preview
GM STAR 250 1986
Бренд: Maico Страницы: 32
R&G CP0478 Fitting Instructions Manual preview
CP0478
Бренд: R&G Страницы: 13
KC N901 User Manual preview
N901
Бренд: KC Страницы: 32
Yamaha FJ-09 2014 Owner'S Manual preview
FJ-09 2014
Бренд: Yamaha Страницы: 126
Leatt 4.0 DBX Manual preview
4.0 DBX
Бренд: Leatt Страницы: 23
DYNATEK DDK3-4 Installation Manual preview
DDK3-4
Бренд: DYNATEK Страницы: 12
hepco & becker 503998 00 01 Manual preview
503998 00 01
Бренд: hepco & becker Страницы: 2
Montesa 4ride Owner'S Manual preview
4ride
Бренд: Montesa Страницы: 114

Бренды по названию

Популярные бренды

Загрузить еще бренды