manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Rear panel

2.

Refit the luggage rack (see Luggage Rack - Installation).
Reconnect the battery positive, (red) lead first and tighten the terminals to 

4.5 Nm

.

Refit the rider’s seat (see Rider’s Seat - Installation).

Rear Mudguard - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the rider’s seat (see Rider’s Seat - Removal).
Disconnect the battery, negative (black) lead first.
Remove the pannier rails (see Pannier Rails - Removal).
Remove the rear panel (see Rear Panel - Removal).
Release the fixing and detach the seat latch from the frame. Discard the fixing.

1.

Detach the seat latch cable from the seat's latch.

2.

chpy

2

3

1

Fixing

1.

Seat latch

2.

Cable

3.

Detach the seat latch outer cable from the subframe.

3.

Note

Note that the fixings for the top of the rear mudguard are fitted with washers. The lower two fixings
are not fitted with washers.

Remove the two fixings and washers from the top of the rear mudguard. Discard the fixings.

4.

3

2

4

Tiger Explorer XR Series

612 of 746

FRAME / BODYWORK

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Kappa K132 Manual preview
K132
Бренд: Kappa Страницы: 4
GAS GAS TXT PRO - 2006 User Manual preview
TXT PRO - 2006
Бренд: GAS GAS Страницы: 56
Happy Trails HTP1-12-7 Quick Start Manual preview
HTP1-12-7
Бренд: Happy Trails Страницы: 3
A3 HELMET TroyLee Designs Owner'S Manual preview
TroyLee Designs
Бренд: A3 HELMET Страницы: 244
Dennis Kirk IGNITE 509 Instruction Manual preview
IGNITE 509
Бренд: Dennis Kirk Страницы: 5
Two Brothers Racing 005-3860405-S1 Installation Instructions preview
005-3860405-S1
Бренд: Two Brothers Racing Страницы: 2
ICON Vehicle Dynamics 57823P Installation Instructions preview
57823P
Бренд: ICON Vehicle Dynamics Страницы: 4
Honda cb500f Service Manual preview
cb500f
Бренд: Honda Страницы: 123
TVS TVS XL 100 Manual preview
TVS XL 100
Бренд: TVS Страницы: 44
Tusk Dry Duffel Bag Instructions preview
Dry Duffel Bag
Бренд: Tusk Страницы: 3
PIAGGIO MSS X9 EVOLUTION 250 Workshop Manual preview
MSS X9 EVOLUTION 250
Бренд: PIAGGIO Страницы: 262
PIAGGIO MP3 500 ie SPORT Business LT 2011 Manual preview
MP3 500 ie SPORT Business LT 2011
Бренд: PIAGGIO Страницы: 375
BMS Cavalier 150 Owner'S Manual preview
Cavalier 150
Бренд: BMS Страницы: 12
Malaguti MADISON 300 2018 User Manual preview
MADISON 300 2018
Бренд: Malaguti Страницы: 120
Malaguti Fast Time F-10 50cc Repair Manual preview
Fast Time F-10 50cc
Бренд: Malaguti Страницы: 151
Baotian BT49QT-11 User Manual preview
BT49QT-11
Бренд: Baotian Страницы: 22
TGB X-MOTION 250 Owner'S Manual preview
X-MOTION 250
Бренд: TGB Страницы: 219
Yamaha 2008 V-Star 1300 Owner'S Manual preview
2008 V-Star 1300
Бренд: Yamaha Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды