manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Cylinder Head Description

The engine is fitted with an aluminium alloy cylinder head, which carries the camshafts, valves and spark plugs.
The cylinder head is cast as a single entity and various components are permanently added after machining.
The camshafts run directly in the cylinder head without separate bearings. Valve clearances are adjusted by
changing variable thickness shims which sit between the valve tappet bucket and the valves.
The camshafts are driven by a silent-type drive chain, via a sprocket bolted to each of the camshafts, using
slotted holes. The use of slotted holes allows the camshaft timing to be adjusted very accurately, to compensate
for manufacturing tolerances in the camshaft drive system.
The chain is guided by two blades and is tensioned by a hydraulic tensioner.
The hydraulic tensioner is fed oil via a gallery in the cylinder head. The combination of oil pressure and spring
pressure pushes the plunger against the tensioner blade which tensions the camshaft drive chain. The hydraulic
tensioner has an oil pressure relief valve located in the plunger that is set to open between 12-16 bar and when
open sprays oil through a drilling in the tensioner blade onto the camshaft drive chain.
Oil is supplied to the cylinder head by a gallery in the crankcase. Once supplied to the head, the oil is distributed
along internal drillings within the cylinder head casting and camshaft.
Single valve springs are used to close both the inlet valves and exhaust valves. These valve springs have close
wound coils at one end to assist in the prevention of valve bounce at high engine speed and to give a smooth
valve actuation. When assembling the cylinder head it is important that the close wound, colour coded ends of
the springs are fitted downwards (towards the piston). Both the tip and seating face of the valves are hardened
to give a long service life.
Due to the methods used to assemble the valve seat and valve guides to the head, these parts cannot be
replaced.

CAUTION

In any of the following operations which necessitate the removal or disconnection of the camshaft drive
chain, NEVER turn the engine without the camshaft drive chain and tensioner correctly fitted and adjusted. In
the disassembled condition, the pistons will contact the valves if the crankshaft is turned, causing severe
engine damage.

Camshaft Drive Chain Tensioner - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the camshaft cover (see Camshaft Cover - Removal).
Remove the right hand crankshaft cover, noting the position of the encapsulated bolt. Discard the

1. 

Tiger Explorer XR Series

84 of 746

CYLINDER HEAD

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

PACIFIC CYCLE none Owner'S Manual preview
none
Бренд: PACIFIC CYCLE Страницы: 112
oset 12.5 Eco Owner'S Manual preview
12.5 Eco
Бренд: oset Страницы: 20
Thunderbike 72-72-125 Installation Instructions Manual preview
72-72-125
Бренд: Thunderbike Страницы: 11
Wolfman Monarch Pass M321 Mounting Instructions preview
Monarch Pass M321
Бренд: Wolfman Страницы: 5
KTM Freeride E-XC 2019 Setup Instructions preview
Freeride E-XC 2019
Бренд: KTM Страницы: 44
MV Agusta F4 750 Instructions Manual preview
F4 750
Бренд: MV Agusta Страницы: 36
GAS GAS EC-SIX DAYS - PART LIST 2011 Parts List preview
EC-SIX DAYS - PART LIST 2011
Бренд: GAS GAS Страницы: 6
R&G ECC0363R Fitting Instructions Manual preview
ECC0363R
Бренд: R&G Страницы: 6
Yamaha YZF600RKC Owner'S Manual preview
YZF600RKC
Бренд: Yamaha Страницы: 130
Yamaha YZF660N 2022 Owner'S Manual preview
YZF660N 2022
Бренд: Yamaha Страницы: 102
Caberg XTRACE Manual preview
XTRACE
Бренд: Caberg Страницы: 16
Yamaha 2005 MT-01 Owner'S Manual preview
2005 MT-01
Бренд: Yamaha Страницы: 90
Yamaha 2005 MT-01 Service Manual preview
2005 MT-01
Бренд: Yamaha Страницы: 435
Yamaha 1990 FZR1000 Assembly Manual preview
1990 FZR1000
Бренд: Yamaha Страницы: 5
Yamaha 1985 XV700 Virago Manual preview
1985 XV700 Virago
Бренд: Yamaha Страницы: 10
Yamaha 1987 FZR1000 Service Information preview
1987 FZR1000
Бренд: Yamaha Страницы: 65
Yamaha 1991 XV250B Owner'S Manual preview
1991 XV250B
Бренд: Yamaha Страницы: 100
Yamaha 1990 XV250A Owner'S Manual preview
1990 XV250A
Бренд: Yamaha Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды