manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

In accordance with the scheduled maintenance chart, inspect the brake fluid level in the front and rear master
cylinder reservoirs.

Ensure that the brake fluid level in the rear brake fluid reservoir is between the upper and lower level lines
(reservoir held horizontal).

1. 

chgp_4

2

1

3

Rear brake fluid reservoir

1.

Rear reservoir upper level

2.

Rear reservoir lower level

3.

To adjust the fluid level:

2.

Remove the two fixings.
Remove the reservoir cap and the diaphragm seal.
Fill the reservoir to the upper level line using new DOT 4 fluid from a sealed container.
Refit the reservoir cap, ensuring that the diaphragm seal is correctly positioned between the cap and
reservoir body.
Refit the two fixings and tighten to 

1.5 Nm

.

Changing Brake Fluid

Brake fluid must be changed every two calendar years, irrespective of the mileage the motorcycle has covered
in that time.

Brake Pads Wear

Front and rear brake pad wear is automatically compensated for and has no effect on brake lever or pedal
action.

Brake Wear Inspection

In accordance with the Scheduled Maintenance chart, inspect the brake pads for wear. The minimum thickness
of lining material for any front or rear brake pad is 1.5 mm. If any pad has worn to the bottom of the groove in the
pad centre, replace all the brake pads on that wheel.

Tiger Explorer XR Series

460 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

National Cycle Spartan N21202 Installation Instructions preview
Spartan N21202
Бренд: National Cycle Страницы: 3
R&G LP0273 Fitting Instructions Manual preview
LP0273
Бренд: R&G Страницы: 22
R&G ECC0337R Fitting Instructions Manual preview
ECC0337R
Бренд: R&G Страницы: 8
CB Sabbiatrici ASTRO 46000 Owner'S Manual preview
ASTRO 46000
Бренд: CB Sabbiatrici Страницы: 43
HERO Splendor Pro CLASSIC Manual preview
Splendor Pro CLASSIC
Бренд: HERO Страницы: 56
hepco & becker 501.4541 00 02 Assembling Instructions preview
501.4541 00 02
Бренд: hepco & becker Страницы: 6
B&G electronics MPA-50M V3 Installation And Operation Manual preview
MPA-50M V3
Бренд: B&G electronics Страницы: 3
Yamaha YZ250(W)/W1 Owner'S Service Manual preview
YZ250(W)/W1
Бренд: Yamaha Страницы: 596
Yamaha YZ250(N)/LC Owner'S Service Manual preview
YZ250(N)/LC
Бренд: Yamaha Страницы: 578
Baja motorsports DR70 Assembly Manual preview
DR70
Бренд: Baja motorsports Страницы: 20
DYNATEK DDK1-8 Installation Manual preview
DDK1-8
Бренд: DYNATEK Страницы: 12
URAL Motorcycles cT 2022 Owner'S Manual preview
cT 2022
Бренд: URAL Motorcycles Страницы: 104
Ops-Core FAST SF Operating Manual preview
FAST SF
Бренд: Ops-Core Страницы: 20
Kinroad XT50-5 Manual preview
XT50-5
Бренд: Kinroad Страницы: 26
Datatool EVO PRO Installation Manual preview
EVO PRO
Бренд: Datatool Страницы: 9
tucanourbano TERMOSCUD R224X Instruction Manual preview
TERMOSCUD R224X
Бренд: tucanourbano Страницы: 4
Cagiva V-Raptor 650 Operation Manual preview
V-Raptor 650
Бренд: Cagiva Страницы: 134
Cagiva 2005 Canyon Owner'S Manual preview
2005 Canyon
Бренд: Cagiva Страницы: 155

Бренды по названию

Популярные бренды

Загрузить еще бренды