manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

CAUTION

The selector forks and shafts can be fitted incorrectly. Ensure the position and orientation of the selector
forks are marked prior to removal. Incorrect fitting of the selector forks or shafts will cause gearbox damage
or incorrect operation.

Note

The two output shaft selector forks are identical. If the selector forks are to be reused, note their
respective positions prior to removal in order that the selector forks can be fitted in their original
locations.

Push the output shaft selector shaft out from the transmission housing in the direction of the output shaft.
Collect each selector fork as they are released by the selector shaft, noting their orientation.

5. 

Remove the two E-clips from the input shaft selector shaft. Discard the E-clips.

6. 

1

chmt

E-clips

1.

CAUTION

The selector forks and shafts can be fitted incorrectly. Ensure the position and orientation of the selector
forks are marked prior to removal. Incorrect fitting of the selector forks or shafts will cause gearbox damage
or incorrect operation.

Push the input shaft selector shaft out from the transmission in the direction of the input shaft. Collect the
selector fork as it is released by the selector shaft, noting its orientation.

7. 

Inspect all bearings for damage or wear. Renew as necessary.
Inspect the selector forks and selector grooves for wear beyond the service limits. Renew the components as
necessary.

Refer to the specifications table (see Transmission).

1.

Selector Drum and Selector Forks - Installation

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Note

Tiger Explorer XR Series

185 of 746

TRANSMISSION 

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Yamaha FJR1300AS Assembly Manual preview
FJR1300AS
Бренд: Yamaha Страницы: 94
Yamaha FJR1300(S) Supplementary Service Manual preview
FJR1300(S)
Бренд: Yamaha Страницы: 44
Yamaha WR250F(R) Owner'S Service Manual preview
WR250F(R)
Бренд: Yamaha Страницы: 860
Öhlins SD 053 Mounting Instructions preview
SD 053
Бренд: Öhlins Страницы: 8
hepco & becker 6616519 01 01 Quick Manual preview
6616519 01 01
Бренд: hepco & becker Страницы: 4
Dowco Fastrax 50144-00 Installation Instructions preview
Fastrax 50144-00
Бренд: Dowco Страницы: 3
KTM Freeride 350 AUS Setup Instructions preview
Freeride 350 AUS
Бренд: KTM Страницы: 25
Can-Am 219 002 095 Operator'S Manual preview
219 002 095
Бренд: Can-Am Страницы: 196
Dakota Digital MCL-4000 Series Manual preview
MCL-4000 Series
Бренд: Dakota Digital Страницы: 3
PIAGGIO Liberty 50 Catalyzed 2019 Manual preview
Liberty 50 Catalyzed 2019
Бренд: PIAGGIO Страницы: 62
Thunderbike Old style Manual preview
Old style
Бренд: Thunderbike Страницы: 7
KTM 690 SMC R 2016 Series Setup Instructions preview
690 SMC R 2016 Series
Бренд: KTM Страницы: 18
Bajaj pulsar F250 Owner'S Manual preview
pulsar F250
Бренд: Bajaj Страницы: 44
Shark Explore-R Manual preview
Explore-R
Бренд: Shark Страницы: 18
Datatool EVO PRO User Manual preview
EVO PRO
Бренд: Datatool Страницы: 5
Yamaha YFM660RP 5LP2-AE2 2002 Supplemental Service Manual preview
YFM660RP 5LP2-AE2 2002
Бренд: Yamaha Страницы: 33
Yamaha YS125-5C 2016 Owner'S Manual preview
YS125-5C 2016
Бренд: Yamaha Страницы: 90
Yamaha YT175J 1982 Service Manual preview
YT175J 1982
Бренд: Yamaha Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды