manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

chpm

1

2

Fuel pump connection

1.

Fuel gauge connection

2.

WARNING

If the fuel rail is dismantled without first reducing pressure, fuel may escape causing clothing and
components to be coated with fuel.
This would represent a serious fire hazard which could lead to burn injuries and damage to property.

Note

Because fuel stored in the fuel rail will be at 3.5 bar pressure, it is essential that the fuel pressure is
reduced before any dismantling of the fuel rail takes place. To reduce pressure, briefly crank the
engine with the fuel pump disconnected.

Briefly crank the engine to reduce the fuel pressure in the fuel rail.

10.

Disconnect the battery, negative (black) lead first.

11.

Note

When disconnected, the fuel tank is self-sealing but a small amount of fuel may dribble from the
hose.
To protect the components under the fuel tank, place suitable material over the components to
absorb the small amount of fuel that may come from the fuel tank and its fuel lines.

Ease the latch away from the fuel connector until the release buttons are exposed.

12.

1

2

Locked position

1.

Unlocked position

2.

Disconnect the fuel hose by squeezing the sides of the connector and pulling the hose free from the spigot.

13.

Note

Use a suitable wooden block to support the rear of the fuel tank when fitting a fuel clamp to the rear
transfer pipe and removing/fitting the transfer pipe to the fuel tank.

Raise the rear of the fuel tank and using one of the fuel clamps from T3880630 - Fuel Hose Clamp, clamp

14.

Tiger Explorer XR Series

303 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

BMW R 1200 C Repair Manual preview
R 1200 C
Бренд: BMW Страницы: 288
Dakota Digital MCL-36K-SPD Installation Manual preview
MCL-36K-SPD
Бренд: Dakota Digital Страницы: 6
GAS GAS FSE 450 - 2006 User Manual preview
FSE 450 - 2006
Бренд: GAS GAS Страницы: 72
Suzuki DR-Z70 Service Manual preview
DR-Z70
Бренд: Suzuki Страницы: 199
DAELIM ROADWIN 125 FI Manual preview
ROADWIN 125 FI
Бренд: DAELIM Страницы: 68
GAS GAS EC 350F Owner'S Manual preview
EC 350F
Бренд: GAS GAS Страницы: 150
TRS One 250 2016 User Manual preview
One 250 2016
Бренд: TRS Страницы: 38
Pandora Smart Moto Manual preview
Smart Moto
Бренд: Pandora Страницы: 56
UBCO 2X2 SE 2023 User Manual preview
2X2 SE 2023
Бренд: UBCO Страницы: 27
SHERCO SHERCO 50 SE 2022 Owner'S Manual preview
SHERCO 50 SE 2022
Бренд: SHERCO Страницы: 226
yasuni TUB807-D57 Assembly Instructions Manual preview
TUB807-D57
Бренд: yasuni Страницы: 9
DYNATEK DDK2-8 Installation & User Manual preview
DDK2-8
Бренд: DYNATEK Страницы: 11
DYNATEK DDK2-4 Installation Manual preview
DDK2-4
Бренд: DYNATEK Страницы: 12
Honeywell PA810EU User Instructions preview
PA810EU
Бренд: Honeywell Страницы: 93
Hudora 84165 Instructions On Assembly And Use preview
84165
Бренд: Hudora Страницы: 8
Magna VF750C Manual preview
VF750C
Бренд: Magna Страницы: 223
Sealey MS052.V2 Instructions preview
MS052.V2
Бренд: Sealey Страницы: 2
APRILIA DORSODURO Manual preview
DORSODURO
Бренд: APRILIA Страницы: 235

Бренды по названию

Популярные бренды

Загрузить еще бренды