manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Note

selected direction.

Click start and check for rear preload motor adjustment collar movement. A maximum of three attempts may
be made to free the motor from an end stop. The attempt to free the motor is successful if adjustment collar
movement is observed.

6. 

Note

If after three attempts to free the motor no adjustment collar movement can be observed, check for
any stored DTCs, rectify as necessary and repeat the rear preload motor test. If the rear preload
motor still doesn’t function correctly, contact Triumph service.

Turn the ignition off and disconnect the Triumph diagnostic tool. Allow 15 seconds for the chassis ECM to
power down.

7. 

Note

With the ignition switch turned off, the Triumph diagnostic tool will prevent the chassis ECM from
powering down if it is left connected to the motorcycle.
To enable the chassis ECM to power down, disconnect the diagnostic tool from the motorcycle.
After running the rear preload motor up/down tests, the rear preload motor will automatically
recalibrate the next time the ignition switch is turned on, provided the chassis ECM is first allowed
to power down.

Turn the ignition switch on and allow the rear preload motor to calibrate, see Rear Suspension Unit Preload
Motor Calibration. During calibration, observe the rear preload motor adjustment collar moving through its
full adjustment range to verify correct motor operation.

8. 

Swinging Arm - Disassembly

WARNING

If the engine has recently been running, the exhaust components may be hot to the touch. Contact with the
hot components may cause damage to exposed skin. To avoid skin damage, always allow the hot parts to
cool before working on the exhaust system.

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the rider’s seat (see Rider’s Seat - Removal).
Disconnect the battery, negative (black) lead first.
Remove the exhaust silencer (see Exhaust System - Removal).
Remove the rear wheel (see Rear Wheel - Removal).
Remove the rear bevel box (see Rear Bevel Box - Removal).
Disconnect the swinging arm position sensor linkage from the swinging arm.

1. 

Disconnect the electrical connector for the rear suspension unit damping solenoid.

2.

Tiger Explorer XR Series

422 of 746

REAR SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Suzuki RV50 Service Manual preview
RV50
Бренд: Suzuki Страницы: 59
SCHUBERTH C3 Limited Manual preview
C3 Limited
Бренд: SCHUBERTH Страницы: 41
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Бренд: kellermann Страницы: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Бренд: BMW Motorrad Страницы: 146
KTM 690 Enduro R 2019 Owner'S Manual preview
690 Enduro R 2019
Бренд: KTM Страницы: 274
Zontes ZT310-X Service Manual preview
ZT310-X
Бренд: Zontes Страницы: 119
X-lite X-902 Directions For Use Manual preview
X-902
Бренд: X-lite Страницы: 84
Dakota Digital MLX-3000 Manual preview
MLX-3000
Бренд: Dakota Digital Страницы: 11
MRA 4025066152438 Mounting Instructions preview
4025066152438
Бренд: MRA Страницы: 8
Ducati Multistrada 620 Owner'S Manual preview
Multistrada 620
Бренд: Ducati Страницы: 382
Yamaha R7 2024 Owner'S Manual preview
R7 2024
Бренд: Yamaha Страницы: 112
Yamaha Star XV250Y Owner'S Manual preview
Star XV250Y
Бренд: Yamaha Страницы: 94
Yamaha Star XVS13CG 2015 Owner'S Manual preview
Star XVS13CG 2015
Бренд: Yamaha Страницы: 98
Yamaha Star XV250G 2015 Owner'S Manual preview
Star XV250G 2015
Бренд: Yamaha Страницы: 88
Yamaha Star XVS13CTD 2012 Owner'S Manual preview
Star XVS13CTD 2012
Бренд: Yamaha Страницы: 104
Yamaha Star XVS11X Owner'S Manual preview
Star XVS11X
Бренд: Yamaha Страницы: 104
Yamaha Star XV250H 2016 Owner'S Manual preview
Star XV250H 2016
Бренд: Yamaha Страницы: 98
Yamaha Star XVS95B Owner'S Manual preview
Star XVS95B
Бренд: Yamaha Страницы: 98

Бренды по названию

Популярные бренды

Загрузить еще бренды