manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

25 Nm

.

Position the brake lever ensuring that the pivot boss is correctly aligned to the push rod. If fitted, position the
handguard bracket as noted during removal.

5. 

Apply a smear of silicone grease to the shank of the brake lever pivot bolt.

6. 

Fit and tighten the pivot bolt to 

1 Nm

.

7.

Counter hold the pivot bolt, fit and tighten the lock nut to 

6 Nm

.

8.

For motorcycles with handguards fitted only:

 Position the handlebar end weight, handguard and spacer

to the handlebar and secure with new fixings. tighten the:

9. 

new handguard to bracket fixing to 

6 Nm

.

new handlebar end fixing to 

5 Nm

.

2

1

5

4

3

Handlebar end fixing

1.

Handguard to bracket fixing

2.

Handguard

3.

Spacer

4.

Handlebar end weight

5.

WARNING

Use only DOT 4 specification brake and clutch fluid as listed in the General Information section of this
manual. The use of brake fluids other than those DOT 4 fluids listed in the General Information section may
reduce the efficiency of the braking system leading to loss of motorcycle control and an accident.
Observe the brake fluid handling warnings given earlier in this section of the manual.

Connect the battery, positive (red) lead first.

10.

Fill and bleed the front brakes (see Bleeding the Front Brakes, Renewing Brake Fluid).

11.

WARNING

Always return the lever adjuster to the original setting noted during removal. Operating the motorcycle with
lever settings which are unfamiliar may lead to loss of control or an accident.

Reset the brake lever adjuster to the original setting.

12.

Examine the system for correct operation and fluid leaks. Rectify as necessary.

13.

Refit the rider’s seat (see Rider’s Seat - Installation).

14.

Check for correct brake operation. Rectify as necessary.

15.

WARNING

Tiger Explorer XR Series

478 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Dennis Kirk IGNITE 509 Instruction Manual preview
IGNITE 509
Бренд: Dennis Kirk Страницы: 5
Bajaj Pulsar 150 DTS-i Maintenance Manual preview
Pulsar 150 DTS-i
Бренд: Bajaj Страницы: 41
Yoshimura RACE 13100CP520 Manual preview
RACE 13100CP520
Бренд: Yoshimura Страницы: 7
Shark OpenLine User Manual preview
OpenLine
Бренд: Shark Страницы: 52
Denali MA11729 Manual preview
MA11729
Бренд: Denali Страницы: 5
B&G electronics MPA-50M V3 Installation And Operation Manual preview
MPA-50M V3
Бренд: B&G electronics Страницы: 3
PerTronix Compu-Fire 55120 32 Installation Instructions preview
Compu-Fire 55120 32
Бренд: PerTronix Страницы: 3
Eastwood 21195 Instructions Manual preview
21195
Бренд: Eastwood Страницы: 8
DYNATEK D3K7-3 Installation Instructions preview
D3K7-3
Бренд: DYNATEK Страницы: 4
DYNATEK D3K1-3 Installation Instructions preview
D3K1-3
Бренд: DYNATEK Страницы: 2
hepco & becker 503998 00 01 Manual preview
503998 00 01
Бренд: hepco & becker Страницы: 2
MSA Gallet F1 XF Operating Manual preview
Gallet F1 XF
Бренд: MSA Страницы: 168
CyClone 866F Owner'S Manual preview
866F
Бренд: CyClone Страницы: 24
EMB Lectra VR24 1998 Owner'S Manual preview
Lectra VR24 1998
Бренд: EMB Страницы: 58
Cagiva V-Raptor 650 Operation Manual preview
V-Raptor 650
Бренд: Cagiva Страницы: 134
Cagiva 2005 Canyon Owner'S Manual preview
2005 Canyon
Бренд: Cagiva Страницы: 155
RIEJU Enduro Owner'S Manual preview
Enduro
Бренд: RIEJU Страницы: 49
RIEJU MRX-SMX 50 Chassis Workshop Manual preview
MRX-SMX 50
Бренд: RIEJU Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды