Triumph Tiger Explorer XR 2016 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 750

background image

WARNING

Before installation, all internal brake components should be cleaned and lubricated with clean new DOT 4
brake fluid.
Never use solvents, petrol (gasoline), engine oil or any other petroleum distillate on internal brake
components as this will cause deterioration of the hydraulic seals in the calipers and master cylinders.
A dangerous riding condition leading to loss of motorcycle control and an accident could result if this warning
is ignored.

Safety Instructions

Jacking and Lifting

WARNING

Always ensure that any lifting apparatus has adequate load and safety capacity for the weight to be lifted.
Ensure the motorcycle is well supported to prevent any possibility of the machine falling prior to lifting or
jacking or while repairs and servicing are carried out.
Never rely on a single means of support when working with the motorcycle. Use additional safety supports
and straps to prevent toppling.
Do not leave tools, lifting equipment, spilled oil, etc. in a place where they could become a hazard to health.
Always work in a clean, tidy area and put all tools away when the work is finished.

Precautions Against Damage

Avoid spilling brake fluid or battery acid on any part of the bodywork. Wash spillages off with water immediately.
Disconnect the battery earth lead before starting work, see

ELECTRICAL PRECAUTIONS

.

Always use the recommended service tool where specified.
Protect exposed bearing and sealing surfaces, and screw threads from damage.

Coolant

WARNING

Coolant mixture, which is blended with antifreeze and corrosion inhibitors contains toxic chemicals which are
harmful to the human body. Never swallow antifreeze, corrosion inhibitors or any of the motorcycle coolant.

WARNING

Do not remove the radiator cap when the engine is hot. When the engine is hot, the coolant inside the
radiator is hot and also under pressure. Contact with the pressurised coolant will cause scalds and skin
damage.

CAUTION

The coolant antifreeze contains a corrosion inhibitor which helps prevent damage to the metal surfaces
inside the cooling system. Without this inhibitor, the coolant would 'attack' the metals and the resulting
corrosion would cause blockages in the cooling system leading to engine overheating and damage. Always
use the correct antifreeze as specified in the Owner's Handbook. Never use a methanol based antifreeze as
this does not contain the required corrosion inhibition properties.

Tiger Explorer XR Series

6 of 746

GENERAL INFORMATION

«
...
8
9
10
11
12
...
»

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Бренд: LAZER Страницы: 13

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренд: KEDO Страницы: 2

Бренд: Yamaha Страницы: 568

Бренд: GAS GAS Страницы: 32

Бренд: hepco & becker Страницы: 2

Бренд: Toolland Страницы: 25

Бренд: DYNATEK Страницы: 5

Бренд: Triumph Страницы: 126

Бренд: Kemppi Страницы: 10

Бренд: JIMS Страницы: 2

Бренд: Shift Power Страницы: 7

Бренд: Shark Страницы: 20

Бренд: Power Fist Страницы: 12

Бренд: Ultra-tow Страницы: 6

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды