manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Always check tyre pressures before riding when the tyres are cold. Operation with incorrectly inflated tyres
may affect handling leading to loss of control and an accident.

WARNING

Operation with excessively worn or damaged tyres will adversely affect handling and control leading to loss
of control or an accident.

WARNING

Inner tubes must only be used on motorcycles fitted with spoked wheels and with tyres marked 'TUBE-TYPE'
unless marked otherwise.
Use of an inner tube with a tyre marked 'TUBELESS' without appropriate marking and/or on an alloy wheel
can lead to loss of motorcycle control and an accident.
All Triumph motorcycles are carefully and extensively tested in a range of riding conditions to ensure that the
most effective tyre combinations are approved for use on each model. It is essential that approved tyre
combinations are used when purchasing replacement tyres as the use of non-approved tyres or approved
tyres in non-approved combinations may lead to motorcycle instability. A list of approved tyres specific to this
model is available from your authorised Triumph dealer, or on the internet at www.triumph.co.uk.

WARNING

If a tyre or inner tube sustains a puncture, the tyre and inner tube must be replaced together. Failure to
replace a punctured tyre and inner tube together, or operation with a repaired tyre or inner tube can lead to
instability, loss of motorcycle control or an accident.
If tyre or inner tube damage is suspected, such as after striking the kerb, ask your authorised Triumph dealer
to inspect the tyre both internally and externally and to also inspect the inner tube. Remember, tyre damage
may not always be visible from the outside. Operation of the motorcycle with damaged tyres could lead to
loss of motorcycle control and an accident.
When replacing a 'TUBE-TYPE' tyre on a spoked wheel, always inspect the rim tape (rim protection band) to
ensure that it is correctly protecting the tube from the spoke threads. A damaged rim tape may lead to rapid
tyre deflation causing loss of control and an accident.

WARNING

Do not install tube-type tyres on tubeless rims. The bead will not seat and the tyres could slip on the rims,
causing tyre deflation that may result in a loss of motorcycle control and an accident.
Do not install an inner tube inside a tubeless tyre unless it is clearly marked on the side wall that you can do
so. This may cause instability and excessive heat build-up may cause the tube to burst resulting in rapid tyre
deflation, loss of vehicle control and an accident.

WARNING

The use of tyres other than those listed at your authorised Triumph dealer, or on the internet, at
www.triumph.co.uk, may adversely affect handling leading to loss of motorcycle control or an accident. Use
the recommended tyre options only in the combinations listed at your authorised Triumph dealer, or on the
internet at www.triumph.co.uk. Do not mix tyres from different manufacturers or tyres from the same
manufacturer but from another option.

WARNING

Tiger Explorer XR Series

548 of 746

WHEELS / TYRES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Yamaha TT-R110E 2017 Owner'S Manual preview
TT-R110E 2017
Бренд: Yamaha Страницы: 88
KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Бренд: KYMCO Страницы: 55
Braaap CRUISER400 User Manual preview
CRUISER400
Бренд: Braaap Страницы: 40
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Бренд: kellermann Страницы: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Бренд: BMW Motorrad Страницы: 146
Memphis Shades MEM-9917 Quick Start Manual preview
MEM-9917
Бренд: Memphis Shades Страницы: 2
Ducati Multistrada 620 Owner'S Manual preview
Multistrada 620
Бренд: Ducati Страницы: 382
Memphis Shades MEB8975 Mounting Instructions preview
MEB8975
Бренд: Memphis Shades Страницы: 2
Yamaha YZ 2019 Series Owner'S Service Manual preview
YZ 2019 Series
Бренд: Yamaha Страницы: 398
Yamaha YZ250F(P)/LC Owner'S Service Manual preview
YZ250F(P)/LC
Бренд: Yamaha Страницы: 666
Yamaha YZ250F(Y) Owner'S Service Manual preview
YZ250F(Y)
Бренд: Yamaha Страницы: 190
Yamaha MT-10 SP 2016 Owner'S Manual preview
MT-10 SP 2016
Бренд: Yamaha Страницы: 118
Yamaha MT09SPN Owner'S Manual preview
MT09SPN
Бренд: Yamaha Страницы: 120
Yamaha MT03M Owner'S Manual preview
MT03M
Бренд: Yamaha Страницы: 106
Yamaha MT10SPN Owner'S Manual preview
MT10SPN
Бренд: Yamaha Страницы: 134
Yamaha MT-10 2023 Owner'S Manual preview
MT-10 2023
Бренд: Yamaha Страницы: 134
Yamaha MT09N Owner'S Manual preview
MT09N
Бренд: Yamaha Страницы: 116
LAS 10323 Operating Instructions Manual preview
10323
Бренд: LAS Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды