Triumph Tiger Explorer XR 2016 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 750

background image

chei

Uppermost fixings

1.

Remove T3880640 - Camshaft Timing Plate by rotating the removal screw clockwise as shown below.

19.

2

3

1

choj

T3880640 - Camshaft Timing Plate

1.

Removal screw

2.

Remove T3880601 - Crankshaft Timing Pin.

20.

CAUTION

Always check that T3880640 - Camshaft Timing Plate has been removed before rotating the engine. Severe
damage will result to the camshafts or T3880640 - Camshaft Timing Plate if engine rotation is attempted with
the tool installed.

Rotate the engine until the remaining two sprocket fixings are accessible.

21.

Remove and discard the two remaining camshaft sprocket fixings, and replace with new fixings. Tighten to

22 Nm

.

22.

Place a suitable wedge between the camshaft drive chain tensioner blade and crankcase, to hold the
camshaft drive chain taut during removal of T3880607 - Camshaft Timing Tensioner.

23.

Release the tension on T3880607 - Camshaft Timing Tensioner and remove it.

24.

Refit the camshaft drive chain tensioner, incorporating a new gasket and O-ring (see Camshaft Drive Chain
Tensioner - Installation).

25.

Fit a new fir tree clip into the hole on the camshaft drive chain tensioner mounting face.

26.

Rotate the engine until T3880601 - Crankshaft Timing Pin can be refitted.

27.

Recheck that the timing marks are still approximately aligned (to check that the camshaft timing has not
moved during the removal of T3880607 - Camshaft Timing Tensioner).

28.

Remove T3880601 - Crankshaft Timing Pin.

29.

Check the valve clearances (see Valve Clearance Measurement). Adjust as necessary (see Valve Clearance
Adjustment).

30.

Valve Clearances

Camshaft, valve, valve shim and valve seat wear affects the valve clearances. The effect of this wear is to
change the gap between the camshaft and tappet bucket, causing engine noise and improper running. If the
valve clearances become too small, permanent damage to the valve and valve seat will take place. If the valve

Tiger Explorer XR Series

98 of 746

CYLINDER HEAD

«
...
100
101
102
103
104
...
»

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Бренд: Cobra Страницы: 2

690 Enduro R 2013

Бренд: KTM Страницы: 234

2005-2006 Hammer

Бренд: Victory Motorcycles Страницы: 12

Power Commander III 718-411

Бренд: Dynojet Страницы: 3

Бренд: TRS Страницы: 38

Бренд: OKBABY Страницы: 35

Easyrack 6612533 01 01

Бренд: hepco & becker Страницы: 5

Бренд: GAS GAS Страницы: 32

Бренд: Zero Страницы: 290

Бренд: Thunderbike Страницы: 7

Бренд: Yamaha Страницы: 104

Super Tenere ABS 2018

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 97

Бренд: DYNATEK Страницы: 4

Бренд: Kask Страницы: 24

Бренд: Tool it Страницы: 26

Бренд: Ops-Core Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды