manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Fluoroelastomer material is used in the manufacture of various seals in Triumph motorcycles.
In fire conditions involving temperatures greater than 315°C this material will decompose and can then be
potentially hazardous. Highly toxic and corrosive decomposition products, including hydrogen fluoride,
carbonyl fluoride, fluorinated olefins and carbon monoxide can be generated and will be present in fumes
from fires.
In the presence of any water or humidity, hydrogen fluoride may dissolve to form extremely corrosive liquid
hydrofluoric acid.
If such conditions exist, do not touch the material and avoid all skin contact. Skin contact with liquid or
decomposition residues can cause painful and penetrating burns leading to permanent, irreversible skin and
tissue damage.

Oils

WARNING

The engine oil may be hot to the touch. Contact with hot oil may cause the skin to be scalded or burned.

WARNING

Prolonged or repeated contact with engine oil can lead to skin dryness, irritation and dermatitis. In addition,
used engine oil contains potentially harmful contaminants which can cause cancer. Wear suitable clothing
and avoid skin contact.

Health Protection Precautions

Avoid prolonged and repeated contact with oils, particularly used engine oils.
Wear protective clothing, including impervious gloves where practicable.
Do not put oily rags in pockets.
Overalls must be cleaned regularly. Discard heavily soiled clothing and oil impregnated footwear.
First aid treatment should be obtained immediately for open cuts and wounds. Always be aware of who your
nearest First Aider is and where the medical facilities are kept.
Use barrier creams, applying before each work period to protect the skin from the effects of oil and grease
and to aid removal of the same after completing work.
Wash with soap and water to ensure all oil is removed (skin cleansers and nail brushes will help).
Preparations containing lanolin replace the natural skin oils which have been removed.
Do not use petrol, kerosene, diesel fuel, gas oil, thinners or solvents for cleaning skin.
If skin disorders develop, obtain medical advice without delay.
Where practicable, degrease components prior to handling.

WARNING

Any risk of eye injury must be avoided. Always wear eye protection when using a hammer, air line, cleaning
agent or where there is ANY risk of flying debris or chemical splashing.

Environmental Protection Precautions

CAUTION

Do not pour oil on the ground, down sewers or drains, or into water courses. To prevent pollution of water

Tiger Explorer XR Series

4 of 746

GENERAL INFORMATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

TVS Apache RTR 160 HYPER EDGE 2015 Owner'S Manual preview
Apache RTR 160 HYPER EDGE 2015
Бренд: TVS Страницы: 60
SW-Motech ALK.00.733.15000/B Mounting Instructions preview
ALK.00.733.15000/B
Бренд: SW-Motech Страницы: 14
Denali SoundBomb TT-SB.10100.B Instruction Manual preview
SoundBomb TT-SB.10100.B
Бренд: Denali Страницы: 3
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Бренд: kellermann Страницы: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Бренд: BMW Motorrad Страницы: 146
BOXER BM 100 Instruction Manual preview
BM 100
Бренд: BOXER Страницы: 11
R&G BLP0097BK Fitting Instructions Manual preview
BLP0097BK
Бренд: R&G Страницы: 8
YCF FACTORY SP2 Owner'S Manual preview
FACTORY SP2
Бренд: YCF Страницы: 78
hepco & becker 654997 01 02 Quick Start Manual preview
654997 01 02
Бренд: hepco & becker Страницы: 2
Yamaha R7 2024 Owner'S Manual preview
R7 2024
Бренд: Yamaha Страницы: 112
DYNATEK DDK3-3 Installation Manual preview
DDK3-3
Бренд: DYNATEK Страницы: 12
Arai GP-6S Operation Instructions preview
GP-6S
Бренд: Arai Страницы: 2
SpeedAngle GMOS JI100S User Manual preview
GMOS JI100S
Бренд: SpeedAngle Страницы: 37
Yamaha XS360 Service Manual preview
XS360
Бренд: Yamaha Страницы: 34
Yamaha XS1-B 650 Owner'S Manual preview
XS1-B 650
Бренд: Yamaha Страницы: 34
Yamaha XJ700N Owner'S Manual preview
XJ700N
Бренд: Yamaha Страницы: 53
Yamaha XJR1300V Owner'S Manual preview
XJR1300V
Бренд: Yamaha Страницы: 90
Yamaha XRS900 Series Owner'S Manual preview
XRS900 Series
Бренд: Yamaha Страницы: 102

Бренды по названию

Популярные бренды

Загрузить еще бренды