manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

2

Swinging arm pivot pin

1.

Locking ring

2.

Pivot pin alignment mark

3.

Frame alignment mark

4.

Note

If the pivot pin and frame markings do not align after final tightening of the locking ring, loosen the
locking ring and right hand pivot pin and repeat steps 30 to 34 of this procedure.

Using T3880062 - Lock Ring Wrench, 38 mm, tighten the locking ring to 

110 Nm

.

34.

Refit the cover to the swinging arm right hand pivot pin.

35.

Remove the support from beneath the engine.

36.

Refit the throttle bodies to the cylinder head (see Throttle Bodies/Injectors - Installation).

37.

Reconnect all electrical connections to the engine and ensure they are secured as noted for removal.

38.

Attach the brake line and its bracket to the crankcase and tighten the new fixing to 

8 Nm

.

39.

Refit the rear bevel box (see Rear Bevel Box - Installation).
Refit the clutch hose to the clutch master cylinder (see Clutch Master Cylinder - Installation).
Fill and bleed the clutch system (see Bleeding the Clutch).
Refit the coolant expansion tank (see Expansion Tank - Installation).
Refit the exhaust system (see Exhaust System - Installation).
Refit the left hand engine bar (see Engine Bars - Installation).
Refit the radiator (see Radiator - Installation).
Refill the cooling system (see Coolant Replacement).
Fill the engine with oil of the correct grade and viscosity (see Oil and Oil Filter Change).
Refit the airbox (see Airbox - Installation).
Refit the fuel tank (see Fuel Tank - Installation).
Remove the motorcycle from its support and place on the side stand.
Refit and connect the battery (see Battery Installation).
Refit the rider's seat (see Rider’s Seat - Installation).

Fuel System and Engine Management

 

Exploded View – Fuel Tank and Fuel Pump

 

Exploded View – Fuel Rail, Throttles and Injectors

Tiger Explorer XR Series

226 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Uclear AMP Series User Manual preview
AMP Series
Бренд: Uclear Страницы: 2
oset 12.5 Eco Owner'S Manual preview
12.5 Eco
Бренд: oset Страницы: 20
R&G CP0473 Fitting Instructions Manual preview
CP0473
Бренд: R&G Страницы: 14
Braaap CRUISER400 User Manual preview
CRUISER400
Бренд: Braaap Страницы: 40
OKBABY No shock Quick Start Manual preview
No shock
Бренд: OKBABY Страницы: 35
Wolfman RTR4 Mounting Instructions preview
RTR4
Бренд: Wolfman Страницы: 3
PIAGGIO MSS X9 EVOLUTION 250 Workshop Manual preview
MSS X9 EVOLUTION 250
Бренд: PIAGGIO Страницы: 262
PIAGGIO MP3 500 ie SPORT Business LT 2011 Manual preview
MP3 500 ie SPORT Business LT 2011
Бренд: PIAGGIO Страницы: 375
Shad HONT72SF Quick Start Manual preview
HONT72SF
Бренд: Shad Страницы: 2
Cagiva Navigator Workshop Manual preview
Navigator
Бренд: Cagiva Страницы: 407
Livall BH6X Series Quick Start Manual preview
BH6X Series
Бренд: Livall Страницы: 44
Honda CRF125F 2020 Owner'S Manual preview
CRF125F 2020
Бренд: Honda Страницы: 192
X-lite X-702 Safety And Instructions For Use preview
X-702
Бренд: X-lite Страницы: 80
GMX MOTORBIKES X Series Assembly Manual preview
X Series
Бренд: GMX MOTORBIKES Страницы: 71
Qingqi QM200GY-B Owner'S Manual preview
QM200GY-B
Бренд: Qingqi Страницы: 39
Dakota Digital UTV-1200 Manual preview
UTV-1200
Бренд: Dakota Digital Страницы: 6
Zero FX 2016 Owner'S Manual preview
FX 2016
Бренд: Zero Страницы: 146
Saito 10030813 Instructions For Use Manual preview
10030813
Бренд: Saito Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды