manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Inlet camshaft

1.

Plain section

2.

Exhaust camshaft

3.

Raised section

4.

Thrust faces

5.

Offset

6.

The same sprocket is used for both inlet and exhaust camshafts, and is attached to the camshaft using slotted
bolt holes. The same holes are used when fitting the sprocket to either camshaft.
Note that the mark on the camshaft boss is not a timing mark, it is used as a visual aid during the timing
adjustment procedure.
Accurate camshaft timing can only be obtained using the correct timing method and service tools (see
Camshafts - Installation).

Camshaft and Bearing Cap Inspection

Inspect the camshaft sprockets for damaged and worn teeth. Replace as necessary.

1.

Measure the camshaft journals with a micrometer. If any journal is outside the specified tolerance, replace
the camshaft.

2. 

For specifications refer toCamshafts.

3.

1

cheg

Camshaft journal

1.

Examine all camshaft and camshaft bearing caps for excessive wear and damage.

4.

Check the journal-to-head clearances, using 'Plastigauge' (Triumph part number 3880150-T0301) as follows:

5.

Wipe the exposed areas of both the camshaft journal and a single cap or cap area of the ladder.
Apply a thin smear of grease to the journal and a small quantity of silicone release agent to the cap.
Size a length of the Plastigauge to fit across the camshaft journal. Fit the Plastigauge to the camshaft journal
using the grease to hold the strip in place.
Ensuring that the camshaft sprocket alignment marking is located as for removal, refit the camshaft cap
ladder then evenly and progressively tighten the ladder bolts to 

10 Nm

 in the correct sequence (see

Camshafts - Installation).
Release the bolts and remove the ladder. Using the gauge provided with the Plastigauge kit, measure the
width of the now compressed Plastigauge.

Tiger Explorer XR Series

93 of 746

CYLINDER HEAD

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Bajaj Pulsar 150 DTS-i Maintenance Manual preview
Pulsar 150 DTS-i
Бренд: Bajaj Страницы: 41
paladin P4009 Installation And Owner'S Manual preview
P4009
Бренд: paladin Страницы: 2
PIAGGIO NRG 50 User Manual preview
NRG 50
Бренд: PIAGGIO Страницы: 275
Bosch DISBLAY DDU 7 Manual preview
DISBLAY DDU 7
Бренд: Bosch Страницы: 160
Shad NADSA W0CG62ST Manual preview
NADSA W0CG62ST
Бренд: Shad Страницы: 12
PUIG 20822 Mounting Instructions preview
20822
Бренд: PUIG Страницы: 3
Ducati Multistrada 1200 ABS Owner'S Manual preview
Multistrada 1200 ABS
Бренд: Ducati Страницы: 199
Ducati PANIGALE V4 2022 Owner'S Manual preview
PANIGALE V4 2022
Бренд: Ducati Страницы: 310
Ducati MONSTER S4 Owner'S Manual preview
MONSTER S4
Бренд: Ducati Страницы: 273
Dynafit BEAST-MIPS User Instructions preview
BEAST-MIPS
Бренд: Dynafit Страницы: 52
R&G FI0119BK Fitting Instructions Manual preview
FI0119BK
Бренд: R&G Страницы: 6
R&G RGH0001BK Fitting Instructions Manual preview
RGH0001BK
Бренд: R&G Страницы: 6
R&G PKS0061 Fitting Instructions Manual preview
PKS0061
Бренд: R&G Страницы: 6
R&G PKS0057SI Fitting Instructions Manual preview
PKS0057SI
Бренд: R&G Страницы: 6
R&G PKS0127SI Fitting Instructions Manual preview
PKS0127SI
Бренд: R&G Страницы: 9
R&G LSR0006 Fitting Instructions Manual preview
LSR0006
Бренд: R&G Страницы: 22
R&G LP0270SI Fitting Instructions Manual preview
LP0270SI
Бренд: R&G Страницы: 20
R&G LP0282 Fitting Instructions Manual preview
LP0282
Бренд: R&G Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды