manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Locking device

1.

Lever

2.

CAUTION

The ABS ECM is an integral part of the ABS modulator. Under no circumstances should the ECM be
removed from the ABS modulator. If a new ECM is required, repair is by replacement of the ABS modulator
and ECM as an assembly only.

Reconnection of the ABS ECM Connector

CAUTION

Damage to the connector pins may result if an attempt to fit the connectors incorrectly is made.

Ensure the lever is fully to the top of the connector.

1.

Align the connector to its socket on the ABS modulator.

2.

CAUTION

If the lever is not moved fully down into it’s locked position, it is possible that the connector may not fully
engage into its socket.

Release the lever by pushing it downwards. At the same time, push the connector into its socket until the
lever is fully down and locked in position. An audible click can be heard when locked.

3. 

The tables that follow will, if used correctly, help to pinpoint a fault in the system once a diagnostic trouble code
has been stored.

Pinpoint Tests

Before Starting Pinpoint Tests:

Delete the stored DTCs.

1.

Switch the ignition OFF and ON.

2.

WARNING

If the ABS is not functioning, the brake system will continue to function as a non-ABS braking system. Do not
continue to ride for longer than is necessary with the indicator light illuminated. Ride with extreme caution
when performing diagnostic troubleshooting on a non-functioning ABS system. In this situation braking too
hard will cause the wheels to lock resulting in loss of motorcycle control and an accident.

Ride the motorcycle at a road speed in excess of 30 km/h. If the DTC is repeated, proceed to the relevant
pinpoint test.

3. 

If the DTC is not repeated, this indicates the DTC may have been stored due to external influences such as
bad road surfaces or electrical interference.

4. 

After Completion of Pinpoint Tests:

Delete the stored DTCs.

1.

Switch the ignition OFF and ON.

2.

Ride the motorcycle at a road speed in excess of 30 km/h. If the DTC is repeated, proceed to the relevant
pinpoint test.

3. 

If a DTC is stored, there is a further fault. Read the stored DTC and refer to the relevant pinpoint test.

4.

Tiger Explorer XR Series

523 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Bajaj Auto CT 100 Manual preview
CT 100
Бренд: Bajaj Auto Страницы: 38
kellermann Atto Integral Installation Manual preview
Atto Integral
Бренд: kellermann Страницы: 2
hepco & becker TRIUMPH Bonneville T 120 Quick Start Manual preview
TRIUMPH Bonneville T 120
Бренд: hepco & becker Страницы: 4
Takegawa 09-12-1010 Instruction Manual preview
09-12-1010
Бренд: Takegawa Страницы: 2
Nuviz NUVIZ User Manual preview
NUVIZ
Бренд: Nuviz Страницы: 46
X-lite X-661 Safety And Instructions For Use preview
X-661
Бренд: X-lite Страницы: 96
Yamaha YZ250(W)/W1 Owner'S Service Manual preview
YZ250(W)/W1
Бренд: Yamaha Страницы: 596
Yamaha YZ250(N)/LC Owner'S Service Manual preview
YZ250(N)/LC
Бренд: Yamaha Страницы: 578
hepco & becker 5054558 00 01 Manual preview
5054558 00 01
Бренд: hepco & becker Страницы: 4
Shad TOPMASTER MOVIL V0X814ST Quick Start Manual preview
TOPMASTER MOVIL V0X814ST
Бренд: Shad Страницы: 2
Wunderlich 8200057 Fitting Instructions preview
8200057
Бренд: Wunderlich Страницы: 4
Wunderlich 35612-001 Fitting Instruction preview
35612-001
Бренд: Wunderlich Страницы: 3
Wunderlich 45181-101 Mounting Instruction preview
45181-101
Бренд: Wunderlich Страницы: 7
Wunderlich 35520-101 Mounting Instructions preview
35520-101
Бренд: Wunderlich Страницы: 9
Can-Am SPYDER RT 2022 Operator'S Manual preview
SPYDER RT 2022
Бренд: Can-Am Страницы: 204
Sealey VS779.V3 Instructions preview
VS779.V3
Бренд: Sealey Страницы: 2
Bagster AP3079 Fitting Instructions preview
AP3079
Бренд: Bagster Страницы: 2
Benelli TnT302S Owner'S Manual preview
TnT302S
Бренд: Benelli Страницы: 55

Бренды по названию

Популярные бренды

Загрузить еще бренды