manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Start the engine and allow to idle until the motorcycle has adapted (see Engine Management Adaption).

Throttle Position Sensor

Note

The throttles cannot be balanced using equipment to measure vacuum in each throttle. Instead, the
Triumph diagnostic tool must be used.

Remove the rider’s seat (see Rider’s Seat - Removal).
Disconnect the battery, negative (black) lead first.
Remove the fuel tank (see Fuel Tank - Removal).
Remove the airbox (see Airbox - Removal).

WARNING

If the engine has recently been running, the components beneath the fuel tank may be hot to the touch.

Temporarily refit the fuel tank and reconnect the fuel supply and fuel pump connection using T3880001 -
Fuel Pressure Gauge (minus the fuel pressure gauge) and T3880123 - Extension Cable (see Fuel Pressure
Checking).

1. 

Using proprietary professional automotive workshop equipment approved for fuel handling, partially refill the
fuel tank with the fuel removed earlier.

2. 

Temporarily reconnect the battery, positive (red) lead first.

3. 

Attach exhaust extraction hoses to the silencers.

4.

Attach the Triumph diagnostic tool, start the engine and navigate to ADJUST TUNE (see Triumph Diagnostic
Software - Engine ECM).

5. 

Select BALANCE THROTTLES.

6.

Adjust Tune Procedure

Adjust the throttle balance as described in the Service Manual until 
balanced
Press cancel to cancel the adjustment process
Press OK to finish

Throttle Status:

Cylinder 1 MAP Pressure:

Cylinder 2 MAP Pressure:

Cylinder 3 MAP Pressure:

Adjusting parameter - Balance Throttles

Throttles Balanced

480 mmHg

480 mmHg

481 mmHg

Balance Throttles Screen

Note

The balance throttles screen shows the vacuum value of each throttle in mmHg. In addition, when
the throttles are balanced to an acceptable range of each other the words 'THROTTLES BALANCED'
in green text will appear on the right of the screen. At this point, no further adjustment is necessary
or productive.
If the throttles are not balanced to each other the words 'THROTTLES UNBALANCED' in red text will
appear on the right of the screen. At this point adjustment will be necessary.
The adjusters operate on the outer cylinders only (cylinders 1 and 3). The centre throttle (cylinder 2)
adjustment is fixed, this being controlled by the throttle control motor. Note that the centre reading
may alter slightly as the two outer cylinders are adjusted.
DO NOT attempt to adjust the throttle stop screws, located below the fuel rail. The stop screws are

Tiger Explorer XR Series

329 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Бренд: KYMCO Страницы: 55
BSA B40 VICTOR W D 1967 Workshop Manual preview
B40 VICTOR W D 1967
Бренд: BSA Страницы: 128
AMFD RideMaxx Quick Start Manual preview
RideMaxx
Бренд: AMFD Страницы: 17
Corbin CA-BAG-ST Manual preview
CA-BAG-ST
Бренд: Corbin Страницы: 4
Rivco VCC094 Quick Start Manual preview
VCC094
Бренд: Rivco Страницы: 5
GAS GAS TXT ROOKIE - 2006 Service Manual preview
TXT ROOKIE - 2006
Бренд: GAS GAS Страницы: 32
Evotech Performance KAWASAKI ZX6R 2007/8 Installation Instructions preview
KAWASAKI ZX6R 2007/8
Бренд: Evotech Performance Страницы: 2
hepco & becker 5054560 00 01 Quick Start Manual preview
5054560 00 01
Бренд: hepco & becker Страницы: 4
Shark Heritage Manual preview
Heritage
Бренд: Shark Страницы: 80
Royal Enfield Super Meteor 650 Owner'S Manual preview
Super Meteor 650
Бренд: Royal Enfield Страницы: 124
Panther R-Bike Owner'S Manual preview
R-Bike
Бренд: Panther Страницы: 47
Xenith X2E Player'S Manual preview
X2E
Бренд: Xenith Страницы: 5
JE-Gauge Daemon III Operation Manual preview
Daemon III
Бренд: JE-Gauge Страницы: 10
Fastway 201742 Instructions For Use Manual preview
201742
Бренд: Fastway Страницы: 64
JTG JT250 2012 User Manual preview
JT250 2012
Бренд: JTG Страницы: 222
LAZER Urbanize User Manual preview
Urbanize
Бренд: LAZER Страницы: 6
BMW C 650 Sport Rider'S Manual preview
C 650 Sport
Бренд: BMW Страницы: 170
Yamaha XVS1300AW 2007 Owner'S Manual preview
XVS1300AW 2007
Бренд: Yamaha Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды