manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

chli

Bleed nipple

1.

Spanner

2.

Bleed tube

3.

Place the other end of the tube in a suitable receptacle containing new brake fluid.

3.

Release the bleed nipple.

4.

Note

During bleeding, do not allow the fluid level to fall below the lower level mark in the reservoir. If the
level is allowed to fall below this mark, air may enter the system and the sequence of bleeding must
be repeated.

Slowly depress the brake pedal and, holding the pedal fully down, close the bleed nipple.

5.

Repeat steps 4 and 5 until no more air appears in the bleed tube.

6.

Note

Maintain the brake fluid level between the upper and lower reservoir levels whilst bleeding is being
carried out.

When all air has been expelled from the system, hold down the brake pedal and close the bleed nipple.
Tighten the nipple to 

6 Nm

.

7. 

Note

If the manual bleed procedure is to be followed by an ABS system bleed, leave the transparent tube
and receptacle in place on the rear caliper.

ABS System Bleed Procedure

Connect the Triumph diagnostic tool (see System Diagnostics).

1.

Follow the on screen menu to ABS Diagnostics. From the menu, select BLEED SYSTEM (see the Triumph
Diagnostic Tool User Guide).

2. 

Note

On pressing the Start button, the diagnostic software will send a command to the ABS ECM to begin
the ABS bleed sequence.
The bleed sequence lasts for 140 seconds and consists of three stages; Flush stage, Bleed stage 1
and Bleed stage 2.
The bleed sequence can be stopped at any time by pressing the Stop button on the diagnostic
software.

Press the Start button to activate the bleed sequence on the diagnostic tool.

3.

Note

The flush stage lasts for 20 seconds. The ABS modulator can be heard operating during the flush
stage and will become silent when the flush stage has completed.

With bleed nipple closed, repeatedly operate the rear brake pedal for the duration of the flush stage.

4.

Note

Bleed stage 1 will start when the flush stage has completed and will be automatically followed by
bleed stage 2.
Bleed stages 1 and 2 last for 60 seconds each. The ABS modulator will remain silent during bleed
stage 1 but can be heard operating during bleed stage 2.

Release the bleed nipple.

5.

Note

During bleeding, do not allow the fluid level to fall below the lower level mark in the reservoir. If the
level is allowed to fall below this mark, air may enter the system and the sequence of bleeding must

Tiger Explorer XR Series

481 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Cobra 602-3000 Instruction Manual preview
602-3000
Бренд: Cobra Страницы: 2
DAELIM ROADWIN 125 FI Manual preview
ROADWIN 125 FI
Бренд: DAELIM Страницы: 68
hepco & becker Easyrack 6617501 01 01 Manual preview
Easyrack 6617501 01 01
Бренд: hepco & becker Страницы: 4
GAS GAS 2007 enducross EC User Manual preview
2007 enducross EC
Бренд: GAS GAS Страницы: 72
kellermann Bullet 1000 RB Installation Manual preview
Bullet 1000 RB
Бренд: kellermann Страницы: 2
hepco & becker 6539521 00 01 Quick Start Manual preview
6539521 00 01
Бренд: hepco & becker Страницы: 5
DYNATEK D2K-HD1E User Instructions preview
D2K-HD1E
Бренд: DYNATEK Страницы: 10
Shark RIDILL Owner'S Manual preview
RIDILL
Бренд: Shark Страницы: 92
Arai GP-6S Operation Instructions preview
GP-6S
Бренд: Arai Страницы: 2
bimota DB5 Mille Owner'S Manual preview
DB5 Mille
Бренд: bimota Страницы: 95
Scott Safety FH4 Operating And Maintenance Instructions Manual preview
FH4
Бренд: Scott Safety Страницы: 67
Shad HONT72SF Quick Start Manual preview
HONT72SF
Бренд: Shad Страницы: 2
Nady Systems HelmetTalk HTCS-3O Installation Manual preview
HelmetTalk HTCS-3O
Бренд: Nady Systems Страницы: 2
Dräger HPS 7000 Instructions For Use Manual preview
HPS 7000
Бренд: Dräger Страницы: 256
Wunderlich F 850 GS Manual preview
F 850 GS
Бренд: Wunderlich Страницы: 6
Sealey VS779.V3 Instructions preview
VS779.V3
Бренд: Sealey Страницы: 2
Power Fist 8808560 Instructions preview
8808560
Бренд: Power Fist Страницы: 2
Power Fist 8674285 User Manual preview
8674285
Бренд: Power Fist Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды