manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Fit a new washer to the drain screw and refit to the crankcase. Tighten to 

8 Nm

.

2. 

Remove the bleed screw from the right hand hose.

3.

1

Bleed screw

1.

With the motorcycle positioned on its side stand, slowly add coolant mixture to the system, through the filler
opening in the radiator, until the system is full.

4. 

If the system has filled correctly and fully, there should be coolant visible through the:

5.

Right hand hose bleed screw opening
Radiator filler opening.
If there is no coolant visible through the right hand hose bleed screw opening, but the filler side appears to
be full, attach a length of clear tubing to the bleed screw spigot and syphon coolant into the bleed screw side
of the radiator.

6. 

Note

A hand-operated vacuum pump or similar should be used to syphon the coolant through the system.

If necessary, top up the system through the filler and refit the pressure cap.

7.

Install the right hand hose bleed screw and tighten to 

1.5 Nm

.

8.

With the aid of an assistant, lean the motorcycle fully over to the right hand side, and then the left hand side,
to release air trapped in the cooling system.

9. 

Remove the radiator cap and top up the coolant.

10.

Refit the cap and repeat as necessary.

11.

Reconnect the battery, positive (red) lead first.

12.

WARNING

Observe the fuel handling precautions given in the General Information section.

Place the fuel tank on a suitable support, close to the motorcycle.

13.

Using T3880123 - Extension Cable, carefully connect the fuel pump connection to the fuel tank. Connect the
other end of the extension cable to the motorcycle main harness.

14. 

Select the fuel pressure gauge adapter marked 'B' from T3880001 - Fuel Pressure Gauge.

15.

WARNING

Always use the correct fuel pressure gauge adapter 

(adapter 'B' for Explorer models)

. Use of an incorrect

adapter will result in a fuel leak. A fuel leak can result in a fire causing damage to property and injury to
persons.

Tiger Explorer XR Series

356 of 746

COOLING

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

R&G CP0504BL Fitting Instructions Manual preview
CP0504BL
Бренд: R&G Страницы: 10
R&G CP0473 Fitting Instructions Manual preview
CP0473
Бренд: R&G Страницы: 14
X-lite X-901 Directions For Use Manual preview
X-901
Бренд: X-lite Страницы: 84
Honda VFR400R Service Manual preview
VFR400R
Бренд: Honda Страницы: 41
hepco & becker 650989 00 02 Manual preview
650989 00 02
Бренд: hepco & becker Страницы: 6
Big Bike Parts 52-571 Installation Instructions preview
52-571
Бренд: Big Bike Parts Страницы: 3
Yamaha ET250 1980 Manual preview
ET250 1980
Бренд: Yamaha Страницы: 22
Yamaha DT50M Manual And Manual preview
DT50M
Бренд: Yamaha Страницы: 24
Yamaha E115M Owner'S Manual preview
E115M
Бренд: Yamaha Страницы: 61
Yamaha Fino 125 Manual preview
Fino 125
Бренд: Yamaha Страницы: 78
Yamaha Fazer Owner'S Manual preview
Fazer
Бренд: Yamaha Страницы: 79
Yamaha FAZER FZS1000 Owner'S Manual preview
FAZER FZS1000
Бренд: Yamaha Страницы: 94
Yamaha Fazer FZ6-S Owner'S Manual preview
Fazer FZ6-S
Бренд: Yamaha Страницы: 90
Yamaha EGO GEAR Owner'S Manual preview
EGO GEAR
Бренд: Yamaha Страницы: 86
Yamaha Fazer FZ6-SHG Owner'S Manual preview
Fazer FZ6-SHG
Бренд: Yamaha Страницы: 96
Yamaha FAZER FZ1-SA Owner'S Manual preview
FAZER FZ1-SA
Бренд: Yamaha Страницы: 96
Yamaha Fazer FZ6-SAHG Owner'S Manual preview
Fazer FZ6-SAHG
Бренд: Yamaha Страницы: 100
Yamaha Fascino 2021 Supplementary Service Manual preview
Fascino 2021
Бренд: Yamaha Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды