manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

when charging or using the battery in an enclosed space.
The battery contains sulphuric acid (electrolyte). Contact with skin or eyes may cause severe burns. Wear
protective clothing and a face shield.
If electrolyte gets on your skin, flush with water immediately.
If electrolyte gets in your eyes, flush with water for at least 15 minutes and SEEK MEDICAL ATTENTION
IMMEDIATELY.
If electrolyte is swallowed, drink large quantities of water and SEEK MEDICAL ATTENTION IMMEDIATELY.
KEEP ELECTROLYTE OUT OF THE REACH OF CHILDREN.

Ensure the VIN number printed on the anti-tamper label attached to the battery matches the motorcycle VIN.

1. 

Check the battery carefully for damage.

2.

CAUTION

Ensure the electrolyte container part number matches the battery part number to be filled. Battery life will be
greatly reduced if the incorrect volume (either too little or too much) of acid is added to the battery.

Read the instructions and warnings delivered with the battery.

3.

Place the battery on a flat level surface and remove the sealing foil.

4.

Remove the battery sealing strip from the electrolyte container and save for later in this procedure. Place the
sealing strip on a clean surface, with the upper side facing downwards to avoid contamination of the sealing
strip. Do not break the seal on the electrolyte container.

5. 

Place the electrolyte container on the battery and fill the battery according to the manufacturers instructions.

6.

After starting to fill the battery with electrolyte, allow the battery to stand for 30 minutes with the filling
container in place.

7. 

Check that all of the electrolyte has drained from the container. Do not remove the container at this point. If
the container has not completely drained, tap the sides of the container to start the electrolyte flowing again.

8. 

After the electrolyte has drained into the battery, allow the battery to stand with the electrolyte container in
place for a further 2 hours.

9. 

Remove the electrolyte container carefully, and dispose of immediately.

10.

Place the sealing cap strip LOOSELY over the filling holes of the battery.

11.

Charge the battery using the BatteryMate Battery Charger - See Latest Parts Catalogue for Part Number
Information. Refer to the instructions supplied with the BatteryMate Battery Charger - See Latest Parts
Catalogue for Part Number Information.

12. 

CAUTION

The caps must be fitted (after charging) within two hours of filling the battery with acid. Leaving the battery
open to the atmosphere for longer than is necessary will start to reverse the chemical reaction which takes
place within the battery, greatly reducing the battery’s service life.

After charging is complete, press down firmly with both hands to seat the caps (do not use tools or force the
caps into position).

13. 

Disconnect the charger and allow the battery to stand for 1 hour before fitting to the motorcycle.

14.

Fit the battery to the motorcycle, positive (red) lead first.

15.

Battery Already in Service

The battery is a sealed type and does not require any maintenance other than checking the voltage and routine
recharging such as during storage.
It is not possible to adjust the electrolyte level in the battery.

Note

The charge level in the battery must be maintained to maximise the battery life.

Tiger Explorer XR Series

630 of 746

ELECTRICAL

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Бренд: kellermann Страницы: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Бренд: BMW Motorrad Страницы: 146
X-lite X-1003 Safety And Instructions For Use preview
X-1003
Бренд: X-lite Страницы: 100
Yamaha R7 2024 Owner'S Manual preview
R7 2024
Бренд: Yamaha Страницы: 112
LAS 10323 Operating Instructions Manual preview
10323
Бренд: LAS Страницы: 22
SUOMY MX SPEED Manual preview
MX SPEED
Бренд: SUOMY Страницы: 26
Bosch DISBLAY DDU 7 Manual preview
DISBLAY DDU 7
Бренд: Bosch Страницы: 160
Memphis Shades 2320-0032 Mounting Instructions preview
2320-0032
Бренд: Memphis Shades Страницы: 2
Razor Crazy Cart XL Replacement Instructions preview
Crazy Cart XL
Бренд: Razor Страницы: 3
Shad TOPMASTER MOVIL V0X814ST Quick Start Manual preview
TOPMASTER MOVIL V0X814ST
Бренд: Shad Страницы: 2
Schweißkraft VarioProtect XXL-W-2 TC Operating Instruction preview
VarioProtect XXL-W-2 TC
Бренд: Schweißkraft Страницы: 16
Bagster AP3079 Fitting Instructions preview
AP3079
Бренд: Bagster Страницы: 2
APRILIA Pegaso 650 2005 Manual preview
Pegaso 650 2005
Бренд: APRILIA Страницы: 139
hepco & becker 7007556 00 01 Mounting Instructions preview
7007556 00 01
Бренд: hepco & becker Страницы: 2
hepco & becker 730.952 Manual preview
730.952
Бренд: hepco & becker Страницы: 8
KTM 450 Rally Factory Replica 2014 Owner'S Manual preview
450 Rally Factory Replica 2014
Бренд: KTM Страницы: 126
Indian Motorcycle 2003 Chief Vintage Service Manual preview
2003 Chief Vintage
Бренд: Indian Motorcycle Страницы: 305
3M Forest XA007707335 User Instruction preview
Forest XA007707335
Бренд: 3M Страницы: 77

Бренды по названию

Популярные бренды

Загрузить еще бренды