manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

leading to loss of motorcycle control and an accident could result if this warning is ignored.

CAUTION

To prevent paint damage, do not spill brake and clutch fluid onto any area of the bodywork. Spilled brake and
clutch fluid will damage paintwork.

To correctly bleed the front brake system, both manual and ABS system bleed procedures must be completed
then repeated in the following sequence:

Complete the manual bleed procedure for the left and right front calipers.
Complete the ABS system bleed procedure.
Repeat the manual bleed procedure.
Repeat the ABS system bleed procedure.
Repeat the manual bleed procedure.

Manual Bleed Procedure

Note

The left hand caliper should be bled first, followed by the right hand caliper.

Working on the left hand caliper first, remove the rubber cap from the bleed nipple on the brake hose union.

1. 

cjje_1

1

2

3

Bleed nipple

1.

Rubber cap

2.

Brake caliper (left hand shown)

3.

Attach a transparent tube to the bleed nipple and place the other end of the tube in a suitable receptacle
containing new brake fluid. Keep the tube end below the level of fluid.

2. 

Release the bleed nipple.

3.

Note

During bleeding, do not allow the fluid level to fall below the lower level mark in the reservoir. If the
fluid level is allowed to fall below this mark, air may enter the system and the sequence of bleeding
must be repeated.

Get an assistant to slowly pull the brake lever to the handlebar.

4.

With the lever held fully against the handlebar, close the bleed nipple. Once the bleed nipple is closed,

5.

Tiger Explorer XR Series

464 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

GAS GAS TXT PRO - 2006 User Manual preview
TXT PRO - 2006
Бренд: GAS GAS Страницы: 56
Öhlins YA 559 Mounting Instructions preview
YA 559
Бренд: Öhlins Страницы: 8
Kabuto HIKE Instruction Manual preview
HIKE
Бренд: Kabuto Страницы: 40
Yamaha MT01X Owner'S Manual preview
MT01X
Бренд: Yamaha Страницы: 92
KTM 690 Enduro R 2013 Repair Manual preview
690 Enduro R 2013
Бренд: KTM Страницы: 234
Victory Motorcycles 2005-2006 Hammer Service Manual preview
2005-2006 Hammer
Бренд: Victory Motorcycles Страницы: 12
RDMOTO CF123 Mounting Instructions preview
CF123
Бренд: RDMOTO Страницы: 2
SHERCO 2015 450 SEF-R Workshop Manual preview
2015 450 SEF-R
Бренд: SHERCO Страницы: 76
TVS WEGO 110 Fi Owner'S Manual preview
WEGO 110 Fi
Бренд: TVS Страницы: 60
Baja motorsports Dirt Runner 90 Owner'S Manual preview
Dirt Runner 90
Бренд: Baja motorsports Страницы: 66
Ducati Superbike 749R 2006 Manual preview
Superbike 749R 2006
Бренд: Ducati Страницы: 608
Yamaha XS650SE Shop Manual preview
XS650SE
Бренд: Yamaha Страницы: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Бренд: Yamaha Страницы: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Бренд: Yamaha Страницы: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Бренд: Yamaha Страницы: 94
BMW S 1000XR 2018 Rider'S Manual preview
S 1000XR 2018
Бренд: BMW Страницы: 241
Husqvarna FC 450 2014 Repair Manual preview
FC 450 2014
Бренд: Husqvarna Страницы: 241
Husqvarna FE 350 2014 Repair Manual preview
FE 350 2014
Бренд: Husqvarna Страницы: 279

Бренды по названию

Популярные бренды

Загрузить еще бренды