manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

the chassis ECM will automatically cut power to the affected system.
The chassis ECM can be reset by turning the Ignition off then on again. Power will be restored to the inoperative
system, providing that the condition that caused the fault has been rectified.
The systems controlled by the chassis ECM are also provided with a secondary level of protection, by fuses PS1
to PS5 in the main fuse box (see Fuse Identification). A blown fuse is likely when all of the systems protected by
that fuse become inoperative.
Refer to the following table for full details of the chassis ECM controlled systems, and their corresponding fuses.

Electrical System

Fuse

Left headlight main beam

PS1

Left headlight dipped beam

Left front direction indicator

Left rear direction indicator

Rear position light

RSU position sensor (models with TSAS only)

Right headlight main beam

PS2

Right headlight dipped beam

Right front direction indicator

Right rear direction indicator

Front position light

Brake light

Windscreen adjustment motor

PS3

RSU pre-load adjustment motor (models with TSAS only)

RSU damping solenoid (models with TSAS only)

Front suspension compression damping adjuster (models with TSAS only)

Front suspension rebound damping adjustment motor (models with TSAS only)

Fog lights (if fitted)

USB connector

Heated seats (if fitted)

PS4

Heated grips (if fitted)

Tiger Explorer XR Series

635 of 746

ELECTRICAL

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

KEEWAY 125-2G Owner'S Manual preview
125-2G
Бренд: KEEWAY Страницы: 15
P.Lindberg KM1501044 Manual preview
KM1501044
Бренд: P.Lindberg Страницы: 26
LAZER Lugano User Manual preview
Lugano
Бренд: LAZER Страницы: 19
Kong MOUSE WORK Manual preview
MOUSE WORK
Бренд: Kong Страницы: 72
Puch Magnum X Service Manual preview
Magnum X
Бренд: Puch Страницы: 151
Yamaha YZ250X 2022 Owner'S Service Manual preview
YZ250X 2022
Бренд: Yamaha Страницы: 276
DYNATEK DDK3-3 Installation Manual preview
DDK3-3
Бренд: DYNATEK Страницы: 12
Shark Explore-R Manual preview
Explore-R
Бренд: Shark Страницы: 18
Xenith EPIC+ Manual preview
EPIC+
Бренд: Xenith Страницы: 7
VESPA GTV 250 i.e. Owner'S Manual preview
GTV 250 i.e.
Бренд: VESPA Страницы: 80
RIEJU RS3 50 Owner'S Manual preview
RS3 50
Бренд: RIEJU Страницы: 280
Starke TR-2503 Operation Manual preview
TR-2503
Бренд: Starke Страницы: 20
VOR 450 Owner'S Manual preview
450
Бренд: VOR Страницы: 102
JAWA 360/00 Owner'S Handbook Manual preview
360/00
Бренд: JAWA Страницы: 40
B&G electronics MPA-50 V3 Installation And Operation Manual preview
MPA-50 V3
Бренд: B&G electronics Страницы: 5
Rockford Fosgate Prime R1-HD2-9813 Manual preview
Prime R1-HD2-9813
Бренд: Rockford Fosgate Страницы: 18
Vento Phantom R4i Service Maintenance Manual preview
Phantom R4i
Бренд: Vento Страницы: 88
Beta RR 125 Instruction Manual preview
RR 125
Бренд: Beta Страницы: 260

Бренды по названию

Популярные бренды

Загрузить еще бренды