manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Starter solenoid

1.

Fixings

2.

Refit the battery tray (see Battery Tray - Installation
Refit the throttle bodies (see Throttle Bodies/Injectors - Installation).
Refit the coolant expansion tank (see Expansion Tank - Installation).
Refit and connect the battery (see Battery Installation).
Refit the rider's seat (see Rider’s Seat - Installation).

If the charging circuit does not operate correctly, the following basic checks must be carried out before further

 

diagnosis is performed:

Check the battery terminals are clean and tight.
Check the frame and engine earth connections are clean, tight and free from corrosion.
Ensure the battery is fully charged and in good condition.
Check that any fuse in the circuit is not blown and is of the correct rating (see Fuses).

Rectify any defects as necessary.
To check the alternator output carry out the alternator pinpoint tests as described below.

Note

The alternator is located under the fuel tank. It does not contain any serviceable parts and must be
replaced if faulty.
The alternator and regulator/rectifier are integrated in the same unit. It is not possible to check for
continuity and short circuit through the coils and to ground.
Do not attempt to open the alternator.
If the battery is not fully charged, the charging Voltage may be lower than specified when checking
at 2,000 rpm.
Ensure all additional accessories (auxiliary lights, heated grips etc.) are switched off.

Fault

Possible Cause

Action

Battery not charging

Battery

Check the condition of the battery
Test the battery using the
BatteryMate 150-9. Refer to the
instructions supplied with the
BatteryMate 150-9
Ensure the battery is serviceable

Alternator/Rectifier/Regulator

Proceed to pinpoint test 1

Pinpoint Tests

Test

Result

Action

1

Check cable and terminal integrity:
- Battery positive (+)
- Battery negative (-)
- Alternator control connector pin 2
- Regulator/Rectifier terminal
- Battery positive connector

OK

Disconnect the battery leads, negative
(black) lead first and proceed to test 2

Faulty

Rectify fault, proceed to test 4

Tiger Explorer XR Series

730 of 746

ELECTRICAL

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

HERO MAESTRO EDGE 125 PROGRAMMED FI Manual preview
MAESTRO EDGE 125 PROGRAMMED FI
Бренд: HERO Страницы: 84
Paaschburg & Wunderlich HIGHSIDER VICTORY Mounting And Safety Instructions preview
HIGHSIDER VICTORY
Бренд: Paaschburg & Wunderlich Страницы: 5
KTM Freeride 350 AUS Setup Instructions preview
Freeride 350 AUS
Бренд: KTM Страницы: 25
KTM 85 SX 2003 Owner'S Manual preview
85 SX 2003
Бренд: KTM Страницы: 38
STARLANE DaVinci RSV4-APRC Installation And Instruction Manual preview
DaVinci RSV4-APRC
Бренд: STARLANE Страницы: 2
KTM F9903S6 Setup Instructions preview
F9903S6
Бренд: KTM Страницы: 26
VStreamT Windscreen N20012A Installation And Owner'S Manual preview
Windscreen N20012A
Бренд: VStreamT Страницы: 3
Bajaj PULSAR NS200 Manual preview
PULSAR NS200
Бренд: Bajaj Страницы: 39
Yamaha Virago XV1100K(C) Owner'S Manual preview
Virago XV1100K(C)
Бренд: Yamaha Страницы: 111
Yamaha VMX EAU10041 Owner'S Manual preview
VMX EAU10041
Бренд: Yamaha Страницы: 101
Yamaha XS650SE Shop Manual preview
XS650SE
Бренд: Yamaha Страницы: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Бренд: Yamaha Страницы: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Бренд: Yamaha Страницы: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Бренд: Yamaha Страницы: 94
hepco & becker 6304554 00 01 Quick Start Manual preview
6304554 00 01
Бренд: hepco & becker Страницы: 4
Hudora 84165 Instructions On Assembly And Use preview
84165
Бренд: Hudora Страницы: 8
R&G FI0134BK Fitting Instructions preview
FI0134BK
Бренд: R&G Страницы: 4
R&G FI0127BK Fitting Instructions preview
FI0127BK
Бренд: R&G Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды