manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Fit the left hand rear cylinder head bolt. Do not fully tighten at this stage.

17. 

Fit a new lock nut to the left hand front cylinder head bolt and tighten to 

24 Nm

.

18.

Tighten the left hand rear cylinder head bolt to 

85 Nm

.

19.

Note

If, after tightening each adjuster and frame fixing, any of the engine to frame alignment bars and
frame fixings cannot be removed and inserted freely, check that the engine is still adequately
supported, loosen all tightened adjusters and frame fixings and restart the tightening sequence from
step 18.

Using T3880377 - Engine Mounting Adjuster, tighten the three adjusters in the following sequence.

20.

Tighten the lower crankcase adjuster to 

5 Nm

.

Tighten the upper crankcase adjuster to 

5 Nm

.

Tighten the cylinder head front right hand adjuster to 

3 Nm

.

chma

1

2

4

3

Lower crankcase adjuster

1.

Upper crankcase adjuster

2.

Cylinder head right hand front adjuster

3.

Adjuster

4.

Remove the upper crankcase alignment bar and fit the upper crankcase bolt and washer from the right hand
side. Holding the bolt to prevent rotation, fit a new lock nut and tighten to 

100 Nm

.

21. 

Remove the lower crankcase alignment bar.

22.

Align the right hand engine protection bar and link bar assembly to the engine. Fit the lower crankcase
mounting bolt through the rear mounting of the engine protection bar, frame and lower crankcase. Loosely fit
a new locknut.

23. 

Position the 13 mm spacer between the engine protection bar centre mounting and the engine as noted for
removal. Fit the M8 x 33 mm bolt, do not fully tighten at this stage.

24. 

2

3

1

2

3

Tiger Explorer XR Series

224 of 746

ENGINE REMOVAL / INSTALLATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Bajaj Auto Avenger 150 Street Owner'S Manual preview
Avenger 150 Street
Бренд: Bajaj Auto Страницы: 40
Öhlins YA 559 Mounting Instructions preview
YA 559
Бренд: Öhlins Страницы: 8
Ohlins HD 907 Mounting Instructions preview
HD 907
Бренд: Ohlins Страницы: 4
KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Бренд: KYMCO Страницы: 55
Dakota Digital MCL-30K-SPD Installation Manual preview
MCL-30K-SPD
Бренд: Dakota Digital Страницы: 7
METRAKIT MINI50 GP 2009 Owner'S Manual preview
MINI50 GP 2009
Бренд: METRAKIT Страницы: 53
R&G ECC0344R Fitting Instructions Manual preview
ECC0344R
Бренд: R&G Страницы: 8
SCHUBERTH C3 Limited Manual preview
C3 Limited
Бренд: SCHUBERTH Страницы: 41
KTM Power Parts 77202923000 Information preview
77202923000
Бренд: KTM Power Parts Страницы: 7
YCF FACTORY SP2 Owner'S Manual preview
FACTORY SP2
Бренд: YCF Страницы: 78
Pandora Smart Moto Manual preview
Smart Moto
Бренд: Pandora Страницы: 56
Yamaha KODIAK YFM70KDXM Owner'S Manual preview
KODIAK YFM70KDXM
Бренд: Yamaha Страницы: 180
Yamaha YFM700R Owner'S Manual preview
YFM700R
Бренд: Yamaha Страницы: 156
Yamaha RAPTOR 700R 2022 Owner'S Manual preview
RAPTOR 700R 2022
Бренд: Yamaha Страницы: 160
KTM 640 LC4 Adventure Owner'S Manual preview
640 LC4 Adventure
Бренд: KTM Страницы: 59
IBEX X-Line Mounting Instruction preview
X-Line
Бренд: IBEX Страницы: 3
R&G FI0087BK Fitting Instructions preview
FI0087BK
Бренд: R&G Страницы: 2
R&G FP0225BK Fitting Instructions Manual preview
FP0225BK
Бренд: R&G Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды