background image

 

 

 

 

INSTALLATION INSTRUCTIONS 

 

 

           

 

 

Cornering Light Kit  Fits GL1500/6 GoldWing 

 

 

 

 

 

 

Part No. 52-571

 

 

 

 

REVISED 2/12/2009

  

 

            

 

TOOLS REQUIRED: 

FLAT BLADED SCREWDRIVER 

 

CYANOACRYLATE ADHESIVE (SUPER GLUE) 

 

 

 

#2 MEDIUM PHILLIPS SCREWDRIVER  

SMALL MARKING PEN 

   HACKSAW 

BLADE 

   CENTER 

PUNCH 

 

 

 

FLAT FILE 

 

 

 

HAMMER 

   KNIFE 

    3/16” 

DRILL 

BIT 

AND 

ELECTRIC 

DRILL 

 
1.  REMOVE THE FOLLOWING: 
 

A. 

PULL OUTWARD ON THE FAIRING FRONT COVER (1A) TO DISENGAGE THE BOSSES (1B) FROM THE FAIRING PANEL COVERS (2A). 

 

B. 

USING THE FLAT BLADE SCREWDRIVER, PRY OFF THE L/R BLACK PLASTIC UPPER SIDE TRIM PIECES.  (2B) 

NOTE:  EACH SIDE  

                HAS ONE LARGE AND ONE SMALL TRIM PIECE TO BE REMOVED. 

 

C. 

USING THE FLAT BLADE SCREWDRIVER, PRY OFF THE SCREW COVER (2C) FROM L/R LOWER FAIRING CORNER MOLDING TRIM       

            

(2D). 

 

D. 

USING THE #2 PHILLIPS SCREWDRIVER, REMOVE THE SCREW (2E) FROM THE L/R LOWER FAIRING CORNER MOLDING TRIM  

              PIECES (2D). 
 

E. 

USING THE #2 PHILLIPS SCREWDRIVER REMOVE THE 3 SCREWS (2F) FROM THE L/R LOWER FAIRING PANEL COVERS (2A). 

 

F. 

REMOVE THE L/R FAIRING PANEL COVERS (2A). 

 
2.  USING THE HACKSAW BLADE, CUT OUT THE L/R K.O. PANELS (3A) USING THE MOLDED SLOTS (3B) AS AN OUTLINE. USING THE FLAT 

FILE, SMOOTH THE CUT EDGES, (4A) FLUSH WITH THE OPENING (4B). 

 
3.  PRESS THE RUBBER MOLDING (5A) ONTO THE EDGES OF THE OPENING (4B) STARTING AT THE BOTTOM CENTER (5B) AND WORKING 

IT ALL THE WAY AROUND THE OPENING BEING CAREFUL NOT TO STRETCH THE MOLDING LENGTH.  TRIM THE EXCESS LENGTH OFF 
TO MATE SQUARELY WITH THE OPPOSITE END. 

 
4.  CAREFULLY PULL THE INSIDE EDGE OF THE MOLDING (5A) AWAY FROM THE L/R COVER.  APPLY A VERY SMALL AMOUNT OF 

CYANOACRYLATE (SUPER GLUE) ADHESIVE BETWEEN THE MOLDING AND THE INSIDE EDGE OF THE OPENING.  

CAUTION:  DO NOT 

GET ADHESIVE ON YOUR FINGERS. 

 
      NOTE:  IF YOU WOULD LIKE A SCREWLESS MOUNT YOU CAN USE POWER POXY PLASTIC BONDER, AVAILABLE AT HARDWARE 

STORES.  BE SURE TO FOLLOW INSTRUCTIONS FOR GLUE.  (GLUING BRACKETS (6A) INSTEAD OF SCREW MOUNTING) 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Copyright© 2005 by Big Bike Parts, Inc. No 
part of this instruction sheet may be 
reproduced without the

 

written permission of 

Big Bike Parts, Inc.  

Отзывы: