Mitsubishi Electric MELSERVO-J2-Super Series, Руководство по переходу

Страница: 603 / 662

[Appendix 2] Introduction to Renewal Tool
Appendix 2-66
5. RENEWAL TOOL CONNECTION DIAGRAM
These diagrams are the connection diagrams for wiring the servo amplifier and servo motor when using the
renewal tool.
* Since a terminal block is not included with the renewal tool (mounting attachment) for 400 V, refer to MR-J4
Servo Amplifier Instruction Manual for the detailed connection.
5.1 SC-J2SJ4(CP)KT02K to 3K
(1) Primary replacement (when replacing the servo amplifier only)
CN3
CN2
CN1A
CN1B
(for SC-J2S(CP)J4KT3K)
(for SC-J2S(CP)J4KT3K)
Make sure to insulate the wiring.
Connection of the built-in regenerative option
(for SC-J2S(CP)J4KT02K to 1K)
Make sure to connect the short-circuit
bar across P and D.
Make sure to
connect the wiring
between P+ and D.
The amplifier capacity is 0.4 kW or less
1-phase 100 V connection
1-phase
100 to 120VAC
1-phase
100VAC
(Note 3)
Power supply
for I/F
(24VDC)
⑦
24VDC power supply
connection cable
⑥
Monitor conversion
cable
Control signal
conversion cable
⑤
Control
signal
Analog
monitor
Encoder
conversion cable
④
Encoder
MR-J2S
servo motor
② ③
Servo amplifier (MR-J4-_A(1)(-RJ))
①
Renewal kit
(SC-J2S(CP)J4KT02 to 3K)
For 3-phase 200 V connection
3- phase
200 to 230VAC
(Note 1)
(Note 2)
(Note 2)
Connection of regenerative option
(for SC-J2S(CP)J4KT02K to 1K)
Regenerative
option
(Note 1)
(Note 1)
(Note 1)
(Note 1)
Regenerative
option
Make sure to remove the wiring for the built-in
regenerative resistor.
Make sure to remove the
wiring between P+ and D.
Note 1. When using the regenerative option, make sure to remove the wiring or the short-circuit bar across P (+) and D, connect with
the wiring between the renewal kit and the servo amplifier, and mount the regenerative option between P and C.
When using a built-in regenerative resistor, make sure to connect the wiring or the short-circuit bar across P (+) and D. For
SC-J2S(CP)J4KT3K, insulate the wiring between the renewal kit and the servo amplifier. Ensure the connection destinations
are correct. The servo amplifier may malfunction if the connection destinations are incorrect.
2. The N terminal of TE2 is limited to SC-J2S(CP)J4KT1K and 3K. There is no D terminal wiring for SC-J2S(CP)J4KT3K.
3. Required only when the internal power supply (24 V DC) for the I/F is used in the existing MR-J2S servo amplifier. Not
included with the renewal tool. Note that a separate 24 V DC power supply (current capacity: 80 mA or more) is required when
replacing.
When connecting the 24 V DC power supply, use the "24 V DC power supply connection cable (model: SC-J2SJ4CTPWC5M)"
included in the package. (Electric wire colors: Red (+ side); white (- side))
No. Product name
①
Servo amplifier *1
②
Servo motor *1
③
Renewal kit
④
Encoder conversion cable
⑤
Control signal conversion cable
⑥
Monitor conversion cable
⑦
24 V DC power supply connection cable
*1: Manufactured by Mitsubishi Electric.
Unassigned
Make sure to remove the short-circuit bar
across P and D. Make sure to remove the wiring between P+
and D.
Make sure to connect the short-circuit
bar across P and D.
Make sure to connect
the wiring between P+
and D.