Mitsubishi Electric MELSERVO-J2-Super Series, Руководство по переходу

Страница: 74 / 662

Part 2: Review on Replacement of MR-J2S-_A_ with MR-J4-_A_
2 - 43
MR-J2S-_A_ MR-J4-_A_
Control
mode
No. Name and function
Initial
value
No. Name and function
Initial
value
66 Gain switching condition
Used to set the values for the gain switching conditions
(command frequency, droop pulses, and servo motor
speed) selected in [Pr. 65].
The set value unit differs depending on the switching
condition item.
Setting range: 0 to 9999
10 PB27 Gain switching condition
Used to set the values for the gain switching
conditions (command frequency, droop pulses, and
servo motor speed) selected in [Pr. PB26].
The set value unit differs depending on the switching
condition item.
Setting range: 0 to 9999
Set the same value as for MR-J2S-_A_.
10 P
S
67 Gain switching time constant
Used to set the time constant at which the gains will
switch in response to the conditions set in [Pr. 65] and
[Pr. 66].
Setting range: 0 to 100
1 PB28 Gain switching time constant
Used to set the time constant at which the gains will
switch in response to the conditions set in [Pr. PB26]
and [Pr. PB27].
Setting range: 0 to 100
Set the same value as for MR-J2S-_A_.
1 P
S
69 Command pulse multiplication numerator 2
Used to set a multiplier for the command pulse. When "0"
is set as the setting value, the resolution of the
connected motor is set automatically.
Setting range: 0 to 65535
When using this parameter, enable the CM1 and CM2
signals in [Pr. 43] to [Pr. 48].
1 PC32 Commanded pulse multiplication numerators 2 to 4
To enable the parameter, select "Electronic gear (0
_ _ _)" or "J3A electronic gear setting value
compatibility mode (2 _ _ _)" in "Electronic gear
selection" in [Pr. PA21].
Setting range: 0 to 16777215
When using this parameter, enable the CM1 and
CM2 signals in [Pr. PD03] to [Pr. PD22].
Set as follows.
(1) For primary replacement
Set the same value as the setting value for MR-
J2S-_A_.
(2) For secondary/simultaneous replacement
Set a value 32 x the MR-J2S-_A_ setting value.
1 P
70 Command pulse multiplication numerator 3
Used to set a multiplier for the command pulse. When "0"
is set as the setting value, the resolution of the
connected motor is set automatically.
Setting range: 0 to 65535
When using this parameter, enable the CM1 and CM2
signals in [Pr. 43] to [Pr. 48].
1 PC33 1 P
71 Command pulse multiplication numerator 4
Used to set a multiplier for the command pulse. When "0"
is set as the setting value, the resolution of the
connected motor is set automatically.
Setting range: 0 to 65535
When using this parameter, enable the CM1 and CM2
signals in [Pr. 43] to [Pr. 48].
1 PC34 1 P
72 Internal speed command 4
Used to set speed 4 of internal speed commands.
When using this parameter, enable the SP3 signal in [Pr.
43] to [Pr. 48].
200 PC08 Internal speed command 4
This is used to set speed 4 of internal speed
commands.
When using this parameter, enable the SP3 signal in
[Pr. PD03] to [Pr. PD22].
Set the same value as for MR-J2S-_A_.
200 S
Internal speed limit 4
Used to set speed 4 of internal speed limits.
When using this parameter, enable the SP3 signal in [Pr.
43] to [Pr. 48]. Internal speed limit 4
This is used to set speed 4 of internal speed limits.
When using this parameter, enable the SP3 signal in
[Pr. PD03] to [Pr. PD22].
Set the same value as for MR-J2S-_A_. T