Mitsubishi Electric MELSERVO-J2-Super Series, Руководство по переходу

Страница: 492 / 662

[Appendix 1] Summary of MR-J4_B_-RJ020 + MR-J4-T20
Appendix 1-29
10. Alarm
10.1 Alarm/Warning List
When an error occurs during operation, an alarm or a warning is displayed. When an alarm or a warning
occurs, take the proper action as described in the "MR-J4-_B_RJ020/MR-J4-T20 Servo Amplifier Instruction
Manual".
After removing the cause of the alarm, the alarm can be canceled using any of the methods marked with
○
in the alarm reset column in the table below. (The shaded parts indicate the differences.)
Number Name
Stop method
(Note 6)
Reset alarm
Power-off to
power-on
Reset an error Reset the CPU
Alarm
10 Undervoltage EDB
12. _ (Note 5) Memory error 1 DB
13 Clock error DB
15 Memory error 2 DB
16 Encoder error 1 DB
17 Board error DB
19. _ Memory error 3 DB
1A Motor combination error DB
20 Encoder error 2 EDB
24 Main circuit error DB
25 Loss of absolute position DB (Note 2)
30 Regenerative error DB (Note 1) (Note 1) (Note 1)
31 Overspeed EDB
32 Overcurrent DB (Note 4) (Note 4)
33 Overvoltage EDB
34 CRC error EDB
35 Command frequency error EDB
36 Transfer error EDB
37 Parameter error DB (Note 4)
3E. 2 Mode change error DB (Note 3)
45 Main circuit element overheat EDB (Note 1) (Note 1, 4) (Note 1, 4)
46 Servo motor overheat DB (Note 1) (Note 1) (Note 1)
50 Overload 1 EDB (Note 1) (Note 1) (Note 1)
51 Overload 2 DB (Note 1) (Note 1) (Note 1)
52 Error excessive EDB
8E Serial communication error EDB
888 Watchdog DB
Warning
92 Battery disconnection warning
Warnings are automatically canceled when the cause is
removed.
96 Home position setting error warning
9F Battery warning
E0 Excessive regeneration alarm
E1 Overload alarm
E3 Absolute position counter alarm
E4 Parameter alarm
E6 Servo forced stop warning EDB (Note 7)
E7 Controller emergency stop warning EDB
E9 Main circuit off warning DB
EE SSCNET error warning
Note 1. After the cause of the alarm is removed, leave it to cool for about 30 minutes.
2. To confirm connection to the servo system controller, the alarm may not be reset if the power is not turned on twice or more.
3. It is only reset when mode is set correctly.
4. Alarm factors may not be removed depending on the cause of the alarm.
5. Numerical figures after a decimal point may not be displayed.
6. There are two stop methods of DB and EDB.
DB: Stop with a dynamic brake
EDB: Stop with an electronic dynamic brake (Only available for the specific servo motor)
Refer to the following table for specific servo motors. The stop method other than the specific servo motor is DB.
Series Servo motor
HG-KR HG-KR053/HG-KR13/HG-KR23/HG-KR43
HG-MR HG-MR053/HG-MR13/HG-MR23/HG-MR43
HG-SR HG-SR51/HG-SR52
7. When STO1 or STO2 is turned off (the CN8 short-circuit connector is disconnected), the stop method is DB.
Display Name Description Cause Action
3E.2 Mode change
error
The operating mode setting does
not match the actual operating
mode. Switched on with the MR-J4-T20
removed. 1. Connect the MR-J4-T20 and restart the servo
amplifier.
2. With the application of "MR-J4(W)-B Change
mode” supplied with the MR Configurator2,
change to "J2S Compatibility Mode".