GigaDevice Semiconductor GD32F10 Series Скачать руководство пользователя

Страница: 688 / 853

GD32F10x User Manual

688

Arbitration for TxDMA and RxDMA controller

There are two types of arbitration method designed for improving the efficiency of DMA

controller between transmission and reception: fixed-priority and round-robin. When DAB bit

in ENET_DMA_BCTL register is reset, arbiter selects round-robin method. The arbiter

allocates the data bus in the ratio set by the RTPR bits in ENET_DMA_BCTL, when both of

TxDMA and RxDMA controller request access simultaneously. When DAB bit in

ENET_DMA_BCTL register is set, arbiter selects fixed-priority, and the RxDMA controller

always has higher priority over the TxDMA.

Error response to DMA controller

During the operation of the DMA controller, when a response error presents on the bus, the

DMA controller considers a fatal error occurs and stops operating at once with error flags

written to the DMA status register (ENET_DMA_STAT). After such fatal error (response error)

occurs, application must reset the Ethernet module and reinitialize the DMA controller.

DMA controller initialization for transmission and reception

Before using the DMA controller, the initialization must be done as follow steps:

Set the bus access parameters by writing the ENET_DMA_BCTL register.

Mask unnecessary interrupt source by configuring the ENET_DMA_INTEN register.

Program the Tx and Rx descriptor table start address by writing the

ENET_DMA_TDTADDR register and the ENET_DMA_RDTADDR register.

Configure filter option by writing related registers.

According to the auto-negotiation result with external PHY, set the SPD bit and DPM bit

for selecting the communication mode (Half-duplex/Full-duplex) and the communication

speed (10Mbit/s or 100Mbit/s). Set the TEN and REN bit in ENET_MAC_CFG register

to enable MAC transmit and receive operations.

Set STE bit and SRE bit in ENET_DMA_CTL register to enable TxDMA controller and

RxDMA controller.

Note:

If the HCLK frequency is too much low, application can enable RxDMA before set REN

bit in ENET_MAC_CFG register to avoid RxFIFO overflow at start time.

TxDMA configuration

Operate on second frame in buffer

When OSF bit in ENET_DMA_CTL is reset, the order of the transmitting is follows: the first is

reading transmit descriptor, followed by reading data from memory and writing to FIFO, then

sending frame data on interface through MAC and last wait frame data transmitting complete

and writing back transmitting status.

Above procedure is TxDMA’s standard transmitting procedure but when HCLK is much faster

Содержание GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32F10 Series

Отзывы:

Похожие инструкции для GD32F10 Series

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32F10 Series, Руководство пользователя

Результаты поиска

Содержание GD32F10 Series

Отзывы:

Похожие инструкции для GD32F10 Series

Бренды по названию

Популярные бренды