manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, Руководство пользователя

Поделиться
Скачать
GigaDevice Semiconductor GD32F10 Series Скачать руководство пользователя страница 356

                                                                                                             

GD32F10x User Manual

 

356

 

 

010: Clear the channel output. O2CPRE signal is forced low  when the counter  is 

equals to the output compare register TIMERx_CH2CV. 

011: Toggle on match. O2CPRE toggles when the counter is equals to the output 

compare register TIMERx_CH2CV. 

100: Force low. O2CPRE is forced to low level. 

101: Force high. O2CPRE is forced to high level. 

110: PWM mode 0. When counting up, O2CPRE is high when the counter is smaller 

than TIMERx_CH2CV, and low otherwise. When counting down, O2CPRE is low 

when the counter is larger than TIMERx_CH2CV, and high otherwise. 

111: PWM mode 1. When counting up, O2CPRE is low when the counter is smaller 

than TIMERx_CH2CV, and high otherwise. When counting down, O2CPRE is high 

when the counter is larger than TIMERx_CH2CV, and low otherwise. 

If  configured  in  PWM  mode,  the  O2CPRE  level  changes  only  when  the  output 

compare mode is adjusted from 

“Timing” mode to “PWM” mode or the comparison 

result changes. 

3 

CH2COMSEN 

Channel 2 compare output shadow enable 

When this bit is set, the shadow register of TIMERx_CH2CV register, which updates 

at each update event will be enabled.   

0: Channel 2 output compare shadow disable 

1: Channel 2 output compare shadow enable 

The PWM mode can be used without verifying the shadow register only in single 

pulse mode (when SPM=1) 

2 

CH2COMFEN 

Channel 2 output compare fast enable 

When  this  bit  is  set,  the  effect  of  an  event  on  the  trigger  in  input  on  the 

capture/compare output will be accelerated if the channel is configured in PWM1 or 

PWM2 mode. The output channel will treat an active edge on the trigger input as a 

compare  match,  and  CH2_O  is  set  to  the  compare  level  independently  from  the 

result of the comparison. 

0: Channel 2 output quickly compare disable.   

1: Channel 2 output quickly compare enable.   

1:0 

CH2MS[1:0] 

Channel 2 I/O mode selection 

This bit-field specifies the work mode of the channel and the input signal selection. 

This  bit-field  is  writable  only  when  the  channel  is  not  active.  (CH2EN  bit  in 

TIMERx_CHCTL2 register is reset).). 

00: Channel 2 is programmed as output mode 

01: Channel 2 is programmed as input mode, IS2 is connected to CI2FE2 

10: Channel 2 is programmed as input mode, IS2 is connected to CI3FE2 

11: Channel 2 is programmed as input mode, IS2 is connected to ITS.   

Note:

  When  CH2MS[1:0]=11,  it  is  necessary  to  select  an  internal  trigger  input   

through TRGS bits in TIMERx_SMCFG register. 

Input capture mode: 

Содержание GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды