manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, Руководство пользователя

Серия полупроводниковых устройств GigaDevice Semiconductor GD32F10 Series обеспечивает высокую производительность и надежность. Пользователи могут получить бесплатное руководство по использованию на manualshive.com, где можно легко загрузить руководства в формате PDF. Узнайте больше о функциях и возможностях этого продукта.

Поделиться
Скачать
background image

                                                                                                             

GD32F10x User Manual

 

236

 

 

12.3.2. 

DAC output buffer   

For  reducing  output  impedance  and  driving  external  loads,  an  output  buffer  is  integrated 
inside each DAC module. 

The output buffer, which is turned on by default, can be turned off by setting the DBOFFx bits 
in the DAC_CTL register. 

12.3.3. 

DAC data configuration 

The  12-bit  DAC  holding  data  (DACx_DH)  can  be  configured  by  writing  any  one  of  these 
registers  (DACx_R12DH,  DACx_L12DH  or  DACx_R8DH).  When  the  data  is  loaded  into 
DACx_R8DH register, only the MSB 8 bits are configurable, the LSB 4 bits are forced to 0. 

12.3.4. 

DAC trigger 

The DAC external trigger is enabled by setting the DTENx bits in the DAC_CTL register. The 
DAC external triggers are  selected  by the  DTSELx bits in the DAC_CTL register, which is 
shown as 

Table 12-2. External triggers of DAC.

 

Table 12-2. External triggers of DAC 

DTSELx[2:0] 

Trigger Source 

Trigger Type 

3b’000 

TIMER5_TRGO 

Hardware trigger 

3b’001 

TIMER2_TRGO in connectivity line devices; 

TIMER7_TRGO in other type devices   

3b’010 

TIMER6_TRGO 

3b’011 

TIMER4_TRGO 

3b’100 

TIMER1_TRGO 

3b’101 

TIMER3_TRGO 

3b’110 

EXTI9 

3b’111 

SWTRIG 

Software trigger 

The TIMERx_TRGO signals are generated from the timers, while the software trigger can be 
generated by setting the SWTRx bits in the DAC_SWT register.

 

12.3.5. 

DAC workflow 

If  the  external  trigger  is  enabled  by  setting  the  DTENx  bit  in  DAC_CTL  register,  the  DAC 
holding data is transferred to the DAC output data (DACx_DO) register when the selected 
trigger  event  happened.  When  the  external  trigger  is  disabled,  the  transfer  is  performed 
automatically. 

When the DAC holding data (DACx_DH) is loaded into the DACx_DO register, after the time 
t

SETTLING

, the analog output is valid, and the value of t

SETTLING

 is related to the power supply 

voltage and the analog output load. 

Содержание GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GD32F10 Series

XVision XD200 User Manual preview
XD200
Бренд: XVision Страницы: 28
YASKAWA CC-Link Installation Manual preview
CC-Link
Бренд: YASKAWA Страницы: 61
ITALFARAD RC4 Operating Instructions Manual preview
RC4
Бренд: ITALFARAD Страницы: 32
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Бренд: YASKAWA Страницы: 12
Wilo AlarmControl 1 Installation And Operating Instructions Manual preview
AlarmControl 1
Бренд: Wilo Страницы: 128
Patton SmartNode 5501 User Manual preview
SmartNode 5501
Бренд: Patton Страницы: 56
Zareba LIS10 User Manual preview
LIS10
Бренд: Zareba Страницы: 40
Renishaw PHC10-3 PLUS Installation Manual preview
PHC10-3 PLUS
Бренд: Renishaw Страницы: 68
Oase 33919 Operating Instructions Manual preview
33919
Бренд: Oase Страницы: 142
Fisher R622 Instruction Manual preview
R622
Бренд: Fisher Страницы: 8
Trio MC508 P848 Quick Start Manual preview
MC508 P848
Бренд: Trio Страницы: 8
thomann Botex DMX RDM Tester User Manual preview
Botex DMX RDM Tester
Бренд: thomann Страницы: 80
Kilews SKP-32BC-60WN Operation And Maintenance Manual preview
SKP-32BC-60WN
Бренд: Kilews Страницы: 11
Oki MSM9225B User Manual preview
MSM9225B
Бренд: Oki Страницы: 92
RKC INSTRUMENT REX-C100 Instruction Manual preview
REX-C100
Бренд: RKC INSTRUMENT Страницы: 8
Hanna Instruments BL 983324-0 Instruction Manual preview
BL 983324-0
Бренд: Hanna Instruments Страницы: 2
North Star 2287181 Owner'S Manual preview
2287181
Бренд: North Star Страницы: 32
Zero 88 Sirius 24 Installation And Operation Instructions preview
Sirius 24
Бренд: Zero 88 Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды