GigaDevice Semiconductor GD32F10 Series Скачать руководство пользователя

Страница: 712 / 853

GD32F10x User Manual

712

This bit controls the receive filter function.

0: Only the frame passed the filter can be forwarded to application.

1: All received frame are forwarded to application. But filter result will also be

updated to receive descriptor status.

30:11

Reserved

Must be kept at reset value.

HPFLT

Hash or perfect filter bit

0: If the HUF or HMF bit is set, only frames that match the hash filter are passed

1: If the HUF or HMF bit is set, the receive filter passes frames that match either

the perfect filtering or the hash filtering

SAFLT

Source address filter bit

Enable source address filtering function besides destination address filtering.

The filter also compares the SA field value in received frames with the values

configured in the enabled SA registers. If SA comparison matches, the SA match

bit in the receive descriptor status is set high

0: Source address function in filter disable

1: Source address function in filter enable

SAIFLT

Source address inverse filtering bit

This bit makes the result of SA matching inverse.

0: Not inverse for source address filtering

1: Inverse source address filtering result. When SA matches the enabled SA

registers, filter marks it as failing the SA address filter

7:6

PCFRM[1:0]

Pass control frames bits

These bits set the forwarding conditions for all control frames (including unicast

and multicast pause frame).

For pause control frame, the processing (not forwarding) depends only on RFCEN

in ENET_MAC_FCTL[2]

0x0: MAC prevents all control frames from reaching the application

0x1: MAC only forwards all other control frames except pause control frame

0x2: MAC forwards all control frames to application even if they fail the address

filter

0x3: MAC forwards control frames that only pass the address filter

BFRMD

Broadcast frames disable bit

0:The address filters pass all received broadcast frames

1:The address filters filter all incoming broadcast frames

MFD

Multicast filter disable bit

0:Filtering of multicast frame depends on the HMF bit

1:All received frames with a multicast destination address (first

bit in the destination address field is '1' and not all bits in the de

stination are ‘1’)

are passed

Содержание GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32F10 Series

Отзывы:

Похожие инструкции для GD32F10 Series

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32F10 Series, Руководство пользователя

Результаты поиска

Содержание GD32F10 Series

Отзывы:

Похожие инструкции для GD32F10 Series

Бренды по названию

Популярные бренды