Hioki MR8827 Instruction Manual Download Page 2

Page: 2 / 436

Contents

Contents

Usage Index ............................................... 1

Introduction ................................................ 2

Package Contents ..................................... 2

Safety Information ..................................... 3

Operation Precautions .............................. 6

Overview 15

1.1 Product Overview ........................... 15

1.2 Part Names and Functions ............ 16

1.3 Screen Organization ...................... 19

Explanation of Screen Contents .................20

1.4 Basic Key Operations .................... 21

1.4.1 Using the HELP Key ....................................22

1.4.2 Use a Mouse to Perform Key Operations .....23

Measurement

Preparation 25

2.1 Install or Remove Modules ............ 26

Channel Allocation ......................................27

2.2 Connection Cables ......................... 28

2.3 Prepare Storage Media .................. 40

2.3.1 Storage Media (Inserting a CF Card and

USB Memory Stick) .....................................40

2.3.2 To Format Storage Media ............................42

2.4 Load Instrument With Recording

Paper (When Model U8350

Printer Unit is installed) ................. 43

2.5 Power Supply ................................. 44

2.5.1 Connect the Power Cord .............................44

2.5.2 Ground the Functional Earth of This

Instrument ...................................................44

2.5.3 Turn the Power On and Off ..........................45

2.6 Set the Clock .................................. 46

2.7 Adjust the Zero Position

(Zero-Adjust) ................................... 47

2.8 Perform Calibration (When

Model MR8990 is installed) ........... 48

Measurement 49

3.1 Measurement Workflow

................. 49

3.2 Pre-measurement Inspection ........ 51

3.3 Measurement Configuration

......... 52

3.3.1 Measurement Function ................................52

3.3.2 Timebase and Sampling Rate ......................54

3.3.3 Recording Length (Number of Divisions) ......57

3.3.4 Screen Layout .............................................59

3.4 Select Input Channels .................... 60

3.4.1 Channel Setting Workflow

............................61

3.4.2 Choose Analog Channel Settings .................63

3.4.3 Logic Channel Settings ................................66

3.4.4 Displayed Sheet...........................................67

3.5 Start and Stop Measurement ........ 68

3.6 Measurement With Automatic

Range Setting (Auto-ranging

Function) ......................................... 70

X-Y Recorder Function 71

4.1 Measurement Workflow

................. 72

4.2 Measurement Configuration

......... 73

4.3 Start and Stop Measurement ........ 74

4.4 Waveform Observation .................. 75

4.4.1 To Save and Print Waveforms......................75

Save/Load Data and

Manage Files

5.1 Data That Can Be Saved and

Loaded ............................................ 79

5.2 Save Data ........................................ 81

5.2.1 Save Types and Workflow

...........................81

5.2.2 Automatically Save Waveforms ...................82

5.2.3 Save Data Selectively (SAVE Key) ..............88

5.2.4 Save Waveform Output Data to the Media ...92

5.3 Load Data ........................................ 93

5.4 Automatically Load Settings

(Auto-setup Function) .................... 96

5.5 Manage Files ................................... 97

5.5.1 Save Data ...................................................98

5.5.2 Check the Contents of a Folder (Open a

Folder) ....................................................... 100

5.5.3 Create New Folders ...................................100

5.5.4 Delete Files and Folders ............................ 101

5.5.5 Sort Files ................................................... 102

5.5.6 Rename Files and Folders .........................103

5.5.7 Copy a File Into a Specified Folder

............104

5.5.8 Print the File List ........................................105

Printing (When Model

U8350 Printer Unit is

installed) 107

6.1 Print Type and Workflow

............. 108

6.2 Auto-print Settings ....................... 109

6.3 Manual Printing With the PRINT

Key (Selective Printing) ................112

6.4 Setting the Print Density of the

Waveform .......................................114

6.5 Printer Settings .............................115

6.6 Miscellaneous Printing

Functions .......................................118

6.6.1 Screen Hard Copy ......................................118

6.6.2 Report Print (A4 Size Print) .........................118

6.6.3 List Print .....................................................119

6.6.4 Text Comment Printing ................................119

MR8827A981-04

Appx.

Index

Appendix

Index

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands