Hioki MR8827 Instruction Manual Download Page 343

Page: 343 / 436

338

External I/O

17.2 External I/O

17.2.1 External Input (START/IN1) (STOP/IN2) (SAVE/IN3)

External control signals can be applied to start and stop measurement and to print and save data. The

factory-default settings are

[Start]

[Stop]

, and

[Save]

Signal Input Procedure

Connect the cables for the corresponding external input signals to the START/IN1, STOP/

IN2, SAVE/.IN3, and GND terminals.

Refer to “17.1 Connect to External Control Terminals” (p. 337).

Press the

SYSTEM

key to open the

[Environment]

sheet, and move the cursor to

[START/

EXT. IN1]

[STOP/EXT. IN2]

, or

[SAVE/EXT. IN3]

Select the operation to be performed by the instrument in response to external signal input.

Start

Start measurement. (not affected by

[START Action]

(p. 307))

Stop

Stop measurement. (Operations after measurement, such as numerical

calculations and automatic saving will be carried out)

Start/Stop

Start measurement on LOW level, and stop measurement on HIGH level.

Abort

Stop measurement immediately. (Operations after measurement, such as

numerical calculations and automatic saving will not be carried out)

Same operation as

PRINT

key (cannot be used with Selective Printing (p. 112))

Save

Save to the media specified for the

SAVE

key, according to the specified

conditions. (cannot be used with Selective Printing (p. 88))

Pen Up/Down

A LOW level signals “pen-down” operation and a HIGH level signals “pen-up”

operation (for X-Y recording).

RUN/STOP

Runs/stops waveform output. (RUN at LOW level, STOP at HIGH level).

PAUSE

Stops waveform output temporarily.

•

For STOP operation, follows the configured

[STOP Action]

(p. 307).

• External input is not available when the HELP screen or a dialog window is displayed.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands