Hioki MR8827 Instruction Manual Download Page 186

Page: 186 / 436

181

Detailed Settings for Modules

Method

Selects the control method for waveform output.

Manual

Restricts control of signal output to Signal Generation screen.

Sync.

Augments manual control with signal output in synchronization with

the start and end of measurement.

START

key: Starts output when measurement starts.

STOP

key: Stops output when measurement stops.

Keys

Augments manual control by allowing signal output to be

manipulated using the instrument’s keys.

START

key: Starts output.

STOP

key: Stops output.

Manual Trigger key: Pauses output.

Settings when selecting arbitrary waveform

Data name

be registered.

Filter

Filter the output waveform.

Off (Default setting) to 1 MHz

Clock Freq

Set the clock frequency of the D/A converter that generates waveforms.

The period and frequency of the output waveform are displayed on the lower level.

Delay

Set the delay for waveform generation. When the delay value is positive, the phase is

progressive.

-250,000 data to 250,000 data (Default settings: 0)

Loop

Set the repetition count for generating waveforms.

1 to 50,000, ∞ (Default setting: ∞)

Amp Adj

Set the amplitude level for waveform output.

Offset

Set the offset voltage for waveform.

Utility Functions

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands