Hioki MR8827 Instruction Manual Download Page 281

Page: 281 / 436

276

FFT Analysis Modes

Waveform Example

Normal display

X axis: Log

Y axis: Lin-Mag

Normal display

X axis: Log

Y axis: Log-Mag

If the cursor is displayed, the total harmonic distortion (THD) with the fundamental wave set to the

cursor position will be displayed. When 2 cursors appear, the A cursor becomes the fundamental wave.

When results cannot be obtained,

[---%]

is displayed.

Power Spectrum Density

Indicates the power spectrum density of the input signal with only the amplitude component

included. This is the power spectrum divided by the frequency resolution.

Main uses:

To acquire a power spectrum with 1-Hz resolution for highly irregular waveforms such as white noise

About the Functions, refer to “13.9.2 Analysis Mode Functions” (p. 289).

Axis

Display type

Description

X axis

Linear

Displays the frequency on a linear scale

Log

Displays the frequency on a logarithm scale

Y axis

Lin-Mag

Displays analysis values linearly.

Log-Mag(logarithm)

Display analysis results as dB values. (0 dB reference value: 1eu

/Hz)*

* eu: engineering units that are currently set are the standard (e.g., when the unit settings is volts, 0 dB = 1 V

/Hz)

Waveform Example

Normal display

X axis: Log

Y axis: Lin-Mag

Normal display

X axis: Log

Y axis: Log-Mag

Not available with external sampling enabled.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands