Hioki MR8827 Instruction Manual Download Page 261

Page: 261 / 436

256

FFT Analysis Condition Settings

13.3.9 Analysis Mode Settings

You can set the type of FFT analysis, channel(s), waveform display color and X and Y axes.

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Status]

sheet.

To set from the Waveform screen, refer to (p. 261).

Display Color Analysis Type

Channel to Analyze

X/Y Axis Display

Analysis Setting

Contents

Analysis No.

Settings can be made from the

dialogs, or copied from another

Analysis No. (p. 163)

Select the FFT analysis mode.

Move the cursor to the

[Analyze]

column of the Analysis No. you wish to set.

Off

No analysis

(Default setting)

Cross Power Spectrum

Storage Waveform

Impulse Response

Histogram

Coherence Function

Linear Spectrum

Phase spectrum

RMS Spectrum

Auto-correlation

Power Spectrum

Cross-correlation

Power Spectrum density*

1/1 Octave*

LPC (density)*

1/3 Octave*

Transfer Function

*Not available with external sampling enabled.

Refer to “13.9.2 Analysis Mode Functions”

(p. 289).

(When

[List]

is selected, a list of calculation types appears. To clear the display, press the

CH.SET

key.)

Select whether the waveform will be displayed and its color.

Move the cursor to the

[Wave]

column.

Select whether to be display (On) the waveform or not, and its color if displayed.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands