Hioki MR8827 Instruction Manual Download Page 22

Page: 22 / 436

Part Names and Functions

Operation Keys

DISP

key

Displays the Waveform screen

STATUS

key

Displays the Status screen

CHAN

key

Displays the Channel screen

FILE

key

Displays the File screen (p. 97)

AB CSR

key

(Lights up in red when selected)

Sets AB cursors (p. 122)

WAVE

key

(Lights up in red when

selected)

Assigns the jog and shuttle

knobs to waveform scrolling.

(p. 126)

Inner:

Jog

Outer:

Shuttle

Scrolls waveforms (p. 126)

CURSOR

key

Moves the cursor up, down, left

and right on the screen.

Manual Trigger

key

Issues a manual trigger event.

(p. 200)

KEY LOCK

When the

ESC

key is pressed for three seconds,

the keys are locked.

To cancel the lock, press the

ESC

key again for

three seconds.

START

key

Starts Measurement

Lights up green during

measurement.

Refer to (p. 307).

SYSTEM

key

Displays the System screen

(p. 305)

TRIG.SET

key

Displays the trigger settings

window on the Waveform

screen. (p. 187)

STOP

key

Stops Measurement

Press once:

Measurement stops after the

set recording length

Press twice:

Stop measurement

Refer to (p. 307).

key

Select setting items

CH.SET

key

Displays the channel settings

window on the Waveform

screen. (p. 60)

AUTO

key

Starts auto-range measurement

(p. 70)

TIME/DIV

key

Sets the time axis.

ESC

key

Cancels an operation.

Removes the displayed dialog

and window.

Overview

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands