Hioki MR8827 Instruction Manual Download Page 8

Page: 8 / 436

Safety Information

Safety Information

This instrument is designed to conform to IEC 61010 Safety Standards, and has been thoroughly tested

for safety prior to shipment. However, using the instrument in a way not described in this manual may

negate the provided safety features.

Before using this instrument, read and understand the following safety notes.

DANGER

Mishandling during use could result in injury or death, as well as damage to the

instrument. Be certain that you understand the instructions and precautions in

the manual before use.

WARNING

Electricity presents risks of electric shock, heat generation, fire, and arc

discharge due to short circuits. If anyone who is unfamiliar with electrical

measuring instruments will use the instrument, a person familiar with such

instruments must supervise operations.

Protective gear

WARNING

This instrument is measured on a live line. To prevent electric shock, use

appropriate protective insulation and adhere to applicable laws and regulations.

Notation

In this manual, the seriousness of risks and hazard levels are classified as follows.

DANGER

Indicates an imminently hazardous situation that will result in death or serious injury to

the operator.

WARNING

Indicates a potentially hazardous situation that may result in death or serious injury to

the operator.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury

to the operator or damage to or malfunction of the instrument.

IMPORTANT

Indicates information related to the operation of the instrument or maintenance tasks

with which the operators must be fully familiar.
Indicates a high voltage hazard.

If a particular safety check is not performed or the instrument is mishandled, this may

give rise to a hazardous situation; the operator may receive an electric shock, be

burned or even be fatally injured.

Indicates prohibited actions.

Indicates actions which must be performed.

Additional information is presented below.

Appx.

Index

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands