Hioki MR8827 Instruction Manual Download Page 277

Page: 277 / 436

272

FFT Analysis Modes

13.9 FFT Analysis Modes

13.9.1

Analysis Modes and Display Examples

For the functions of each analysis mode, refer to “13.9.2 Analysis Mode Functions” (p. 289).

Storage

Displays the time-domain waveform of the input signal.

When the window function setting is other than rectangular, the window function is applied to the

time-domain waveform before it is displayed.

Axis

Display type

Description

X axis

Linear

Time-domain display

Displays the value of the time-domain waveform corresponding to the set

frequency range.

Refer to “Relationship Between Frequency Range, Resolution and Number of

Analysis Points” (p. 248).

Y axis

Lin-Mag

Displays the module waveform

Waveform Example

Window: Rectangular

X axis: Linear

Y axis: Lin-Mag

Histogram

Acquires the amplitude distribution of the input signal.

Main uses:

• To inspect deviations in the amplitude range of a waveform

•

Uses analysis point distribution to ascertain whether a waveform is artificial or natural

About the Functions, refer to “13.9.2 Analysis Mode Functions” (p. 289).

Axis

Display type

Description

X axis

Linear

Displays input level of the input signal.

Y axis

Lin-Mag

Displays analysis data distribution.

Waveform Example

Normal display

X axis: Linear

Y axis: Lin-Mag

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands