Hioki MR8827 Instruction Manual Download Page 73

Page: 73 / 436

Start and Stop Measurement

3.5 Start and Stop Measurement

Procedure

Press the

DISP

key to open the Waveform screen.

To Start Measurement

Press the

START

key to start measurement.

• When a measurement is started, waveform data displayed on the screen is cleared.

• Measurement can also be started by applying a signal to the external control terminal.

Refer to “17 External Control” (p. 335).

To prevent inadvertently starting measurement

To prevent operation mistakes from unintentionally starting measurement, the

START

key operation

method can be changed.

Refer to “Start Action” (p. 307).

To automatically save data during measurement

Refer to “5.2.2 Automatically Save Waveforms” (p. 82).

To print the waveform

Refer to “6 Printing (When Model U8350 Printer Unit is installed)” (p. 107).

To Stop Measurement

Press the

STOP

key once to stop recording at the end of the specified recording length.

Press the

STOP

key again to stop recording immediately.

The operation conditions for the

START

and

STOP

keys can be changed.

Refer to “15 System Environment Settings” (p. 305).

When

STOP

is pressed, the following indication may appear on the screen.

Measurement will stop at the point where the key is pressed.

(Pressing the

STOP

key twice has the same effect.)

The stopping procedure will be canceled and measurement will continue.

When no key operation is made in this status, the measurement will stop at the end of the specified

recording length and the display returns to the previous screen.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands